13 December 2019 3 8K Report

We are looking for thermocouple which is suitable for 1300 degC and 25 bar pressure. Please suggest us the suitable one for the above application. If possible please share the links of the same.

More Muddada Ganapathi's questions See All
How to prevent the growth of algae and scale formation in water tanks?

We are looking for disinfectants which can prevent the algae and scale formation in water tanks(Stainless Steel). It would be great if you share any online vendor links which can provide such...

01 June 2020 2,443 0 View

How to find the volume flow rate of products after a combustion reaction in a reactor?

We need to calculate the volume flow rate of the products of a particular chemical reaction which will be takes place in a reactor. How can we get the products volume flow rate if we have the...

09 February 2020 3,277 3 View

What type of gasket is better suitable for flat flanges in high temperature and pressure applications?

We are searching for the high pressure (20 bar) and temperature (900 deg C) gaskets. Which type of material gaskets can be used for flat flanges. Please suggest me any gasket material for the...

19 December 2019 4,261 2 View

How to design high pressure, high temperature steam generator?

We need to heat up the steam from its saturated state to a superheated state at 2 bar and 20 bar pressures. What are the things need to be considered while designing the heater requirement? Which...

28 November 2019 190 0 View

Through which way I can learn COMSOL Multiphysics software effectively?

I would like to learn COMSOL Multi-physics software to undertake my project. Anyone of you have any source through which it is possible to get better handling experience of it? Please share the...

10 June 2019 1,532 2 View

Which pipe has more heat transfer capacity out of plain and corrugated?

What is the difference in heat transfer will take place when we use corrugated pipes in shell and tube heat exchanger instead of plain type? If anyone have any reference regarding the above,...

10 June 2019 8,141 6 View

How to design an effective double helical heat Exchanger?

I would like to fabricate a double helical heat exchanger for heating the steam from 100 degC to 450 degC by passing the flue gases with inlet temperature of 1200 degC and outlet temperature...

10 June 2019 3,343 8 View

What fixture pressure generally gives in tensile test of Aluminium rod under UTM?

Input fixture pressure, while doing the tensile test, so that it can be stabled properly.

28 June 2017 5,378 3 View

How do we get the 2 theta angle values in the interval of 0.025 by using any xrd software?

Actually I have XRD data but I am unable to get 2 theta and corresponding intensity value in the interval of 0.025. I want any software in which that facility is available. So, please give me a...

01 January 1970 4,842 2 View

Similar questions and discussions
Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

How to improve peaks separation in HPLC?

Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...

30 July 2024 435 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

AGILENT HPLC 1100 SERIES , any expert available please?

AGILENT HPLC 1100 SERIES operation assistance needed.

25 July 2024 10,045 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close