Which simulator is best suited for IoT security?

More Mansur Kabir Dankaura Mansur's questions See All

How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How to convert all .csv file to grayscale image and then save them?

I have a database of experiment .csv files. how to extract the feature from this .CSV file with max-min normalization? I need a matrix(with values between 0 to 255) to be converted to a grayscale...

04 February 2021 7,773 3 View

How to rectify the miscomputation of Pressure and Continuity in HVAC CFD Simulation Using OpenFOAM?

I'm using OpenFOAM to run a CFD study of thermal comfort within a hall. I'm using OpenFOAM v1912 and BouyantBoussinesq(Simple&Pimple)Foam solver. eI have 6 inlets and outlets each with specific...

21 December 2020 1,303 3 View

Is there any other microbes (except microalgae) that could efficiently remove nitrogen and phosphorus content from wastewater ?

I was studying the biological treatment (anaerobic) of wastewater biomass. I found that anaerobic bacteria take a comparatively longer time to biodegrade nitrogenous compounds. Is there any other...

28 October 2020 921 3 View

Can I perform a Benjamini Hochberg FDR correction over p values from different tests?

I'm performing statistical analysis on a time series data, comparing the average amplitude (y axis) between three groups on every 50 ms (x axis). The time series is 1200 ms long (so in total 24...

21 October 2020 3,269 3 View

Would you suggest me a formula for calculating energy yield from biohydrogen and biomethane production?

I was looking for a formula to calculated the obtained energy yield via biohydrogen and biomethane production using anaerobic digestion process. The unit is in SI unit (x) mLH2/g VS and (y) mL...

20 October 2020 8,668 5 View

Is my retinal GFAP staining accurate?

I am doing immunofluorescence staining on retinal sections from RCS rats to assess GFAP. As shown in my attached image, the GFAP staining is not consistent with most literature I've seen with...

05 October 2020 8,105 3 View

Is it possible to do image processing using Arduino/NodeMCU? If so, which camera module would be better?

We have already completed a project where we have done image processing using raspberry pi. Now we want to do the project using Arduino / NodeMCU.

28 September 2020 1,486 3 View

What Important factors should I keep in mind while writing a review paper?

I am trying to write my first review paper. I don't have much knowledge about writing it. If you could provide me with some valuable points, I would be very thankful.

15 September 2020 10,025 10 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

How vulnerable is water and wastewater infrastructure to cyber terrorism in an age of IoT?

Im looking for any papers, reports,articles, links etc on information on How vulnerable is water and wastewater infrastructure to cyber terrorism in an age of IoT.

24 February 2021 2,750 4 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View