08 August 2018 0 2K Report
  • Oxide dispersion strengthened (ODS ) Steel

More Ratnakar Singh's questions See All
Can we confirm equiaxed grains by seeing selected area diffraction pattern (SADP) obtained from TEM?

Transmission Electron Microscope, Materials Characterization

08 September 2018 6,807 3 View

Can we calculate phase fraction by X-Ray Diffraction?

Materials Characterization

08 September 2018 4,313 3 View

What is the information we can get from Small angle X-Ray scattering( SAXS)? and how it is different from normal X-Ray diffraction (XRD) technique?

Small Angle X-Ray Diffraction (SAXS), X-Ray diffraction(XRD)

08 September 2018 7,403 5 View

Similar questions and discussions
12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

What is the best solvent to remove PDMS from nano particles?

I want to remove PDMS oligomers from the surface of nanolayers. I have just read a very helpful paper about the compatibility of PDMS with different solvents( Solvent Compatibility of...

24 February 2021 7,845 5 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close