Which book suitable for “Crop modeling” procedures with exercise ?
Dear sir, U can follow the book entitled "Crop growth simulation modelling and climate change" of Dr M Mohanty et al
Thanks Dear Dr. Mahipal Choudhary for your valuable inputs and suggestions
Sincerely,
Vijay
Crop modeling and production system
Dear Dr. Latief Ahmad please gives details of this book, please
Sincerely
How to write the research project proposal in early career ?
02 March 2018 8,276 1 View
In general knowledge, soil microbial C/N ratio is 4:1-9:1 but in our case after verification and re-measurement the C:N ratio is ~ 50% of reported ratio (1.8:1-2.5:1). But we could not understand...
01 February 2018 7,311 3 View
There are many more corrections in the Abstract itself and also the rest of the manuscript. Therefore, I can give one last chance to get the manuscript edited for the language from a native...
07 August 2017 2,220 24 View
In which journal we can communicate the policy paper?
04 May 2017 6,094 0 View
What are the best methods for soil moisture measurement? Field as well as Lab.
07 August 2016 8,178 7 View
Respected Sir/madam Please tell me in detail of the above mentioned question
05 June 2016 1,642 3 View
Dear all RG respected members, please suggest me how to improve English of the manuscript?
10 November 2015 9,259 3 View
What is the right procedure for the application of fertilization in pot experiments? I am awaiting your valuable suggestions.
10 November 2015 5,582 18 View
What is the use of nanotechnology with PGPR in evergreen agriculture?
08 September 2015 4,390 1 View
Dear All, Can anyone give me an idea regarding to write project (s) as following areas: - and also suggest funding agencies 1. C-sequestration under changing climatic scenarios 2. Soil as well...
08 September 2015 807 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.
05 August 2024 2,977 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...
04 August 2024 3,461 3 View