Whether Canonical Correlation or Path Modeling is suitable for to interpret dimensions of two variables?

07 July 2018 0 5K Report

There are five dimensions of Knowledge Management (KM) and four dimensions of Academic Performance (AP). Which test is suitable to measure the inter-dependencies between these two variables (i.e, KM and AP) ?

Badges
Science topic

Similar topics
Engineering
Modeling

More Krishna Pd. Paudel's questions See All

In which condition we apply design effect?

What is the logic behind to use design effect during calculation of sample size?

06 July 2018 3,823 4 View

In which condition we can apply 99% of confidence level?

06 July 2018 10,257 3 View

How can we link the relationship between Knowledge Management Practices and Academic Performance in Higher Education Institutions?

How the faculty member's academic performance can be linked with individual knowledge management practices behavior?

04 May 2018 4,331 6 View

Design Effect or 99% of CI to increase sample size

In which condition we apply 99% of CI. Which method is appropriate to increase number of sample size either through 99% of CI or going through design effect.

01 January 1970 7,175 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How can I interpret the data without the need of solving it manually?

How can I interpret the data gathered without solving?

03 August 2024 9,054 3 View