Where have be found good examples of Performance evalutions criteria (PEC) for Heat exchanger with cicrular finned tubes?

More Mladen Bošnjaković's questions See All

Heat transfer coefficient on shell side of shell and tube HE?

Hot water enters on the shell side and cools along the tubes. Why does the heat transfer coefficient decrease along the tubes and have a lower value at the water outlet? And why does the heat...

17 October 2022 3,642 4 View

How to set correct Convergence Tolerance?

I am solving heat finned tube heat exchanger. At Residual monitor is default setings for Convergence Tolerance. All values is set to 0,001 exep energy to 1e-06. If velocity of air at input is 2...

31 January 2017 1,182 9 View

Does Inflating layers need to be on both sides: on fluid and solid body?

Object of interest is fluid flow over tube in heat exchanger. Does Inflating layers need to be on both sides: on fluid side (air) and solid body (tube)? If yes, thus number of layer have to be...

14 January 2017 1,294 5 View

Capillary flow in PHOENICS?

Currently, I am working on the simulation of capillary flow in PHOENICS. The idea is to insert the PATCH with pressure conditions as the result of surface tension. I'm am using H-O-L and SGS as...

08 January 2017 4,166 1 View

Does anyone know of any work where time-out in volleyball is processed?

Does anyone know of any work where time-out in volleyball is processed? Thanks. Time before the calling time-out... time after finished time-out?

27 December 2015 6,528 4 View

Reversibile flow on outlet in ansys Fluent?

I make calculation of my model of finned heat exchangers by Ansys Fluent. Model is somewhat complicated and have abut 5 millions elements and 8 inflation's layers. I chose k-epsilon method for...

01 January 1970 3,867 12 View

How to solve divergence problem?

I am trying to solve my model of heat exchanger with finned tubes in Fluent. First variant with air velocity of 1 m/s converged after cca 550 iteration in k-epsilon model. Now I choose velocity of...

01 January 1970 9,569 17 View

How to import correct model for ANSYS FLUENT?

I made a model of the heat exchanger in SolidWorks. The goal is to make numerical simulation using ANSYS FLUENT (ver 15.0). So far I have not used the said program is likely to be adapted designed...

01 January 1970 1,758 3 View

How to define the air properties in the heat exchanger calculation: as constant or temperature dependent?

I calculate Heat exchanger air-water, the air is heated. The air at the entrance is about 20 C. Ansys offers the ability to define air properties (density, thermal conductivity, dynamic viscosity...

01 January 1970 1,069 2 View

How many visual identity of an institution affects attracting students to study at that institution?

Students choose faculty based on multiple factors: their desires, financial opportunities, employment opportunities after studying, colleagues 'recommendations, parents' wishes and so on. The...

01 January 1970 9,817 0 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Brian Hanley

Try to get hold of the book "Compact Heat Exchangers" by Kays and London.

Mladen Bošnjaković

Brian,

OK, thanks.

Ahmed Al-Sammarraie

Hi Mladen,

Try to get this book:

"HEAT EXCHANGERS; Selection, Rating, and Thermal Design" by Kakaç, S., Liu, H., Pramuanjaroenkij, A.

Best regards,

Ahmed

Ok, thanks.

Ok, thanks Lucky.