28 September 2017 3 5K Report

I'm working on a paper about the relation between urban morphology and climate changes. I need the maps in order to compare the terrain use back in 1980 and current situation  to simulate the data by CFD. 

More Mehdi Makvandi's questions See All
Multi effect distillation modeling in EES?

Dear colleagues If anyone has a model of multi-effect distillation in EES or MATLAB software, please send it to me.

24 February 2021 7,282 1 View

Can we recognize signs of the "volatility clustering" property of a time series in its time domain plot?

My purpose is to recognize the volatility clustering property without statistical tests such as The Lagrange Multiplier (LM) test.

24 February 2021 4,150 3 View

How to define a new PDE in COMSOL?

(Note: Problem Solved) I am trying to define the phase field equation in the picture, using Coefficient form (or maybe convection-diffusion) PDE in COMSOL. However, I have a problem defining the...

06 January 2021 3,790 9 View

I need suggestions about my submitted manuscript which is taking abnormally long time?

Dear all I hope you are doing great and healthy. My question is about the abnormally long time being taken by the peer-review process of my submitted manuscript. I submitted my article in July...

21 December 2020 1,432 4 View

Why the number of secondary depressions on existing chromosomes varies?

Why the number of secondary depressions on existing chromosomes varies?

15 November 2020 9,614 3 View

What should I interpret from the following TGA curves?

I have coated my adsorbent with SiO2 layer using Stober's method. I have performed the TGA for both the samples and as you can see from the images attached, they are completely different. From...

31 October 2020 9,390 9 View

How can I couple x-coordinates with y-z coordinates in COMSOL?

Hi, I want to couple x-coordinates with y-z coordinates so that the shape of the whole plate looks same movement. For example, if cross-section of the plate i.e. y-z axis shows deflection then...

25 September 2020 5,941 3 View

What is the best method for commercial production of Astaxanthin from Haematococcus pluvialis?

Dear Friends, I'm looking for a reference that has extensively explained the best method to increase the biomass of Haematococcus pluvialis algae as well as the extraction of Astaxanthin from it....

30 August 2020 2,920 3 View

Which parameters to look in the Baseline report to determine the worst Cytometer for an harmonization?

I would like to harmonize different cytometers because I have a lot samples to analyze. To perform this harmonization I need to know which device is the least efficient? Could someone tell me...

09 August 2020 5,529 4 View

Which journal do you suggest for publishing a crystal structure report?

Which journal do you suggest for publishing a crystal structure report?(it is better that the journal bee in JCR and free of charge)

27 July 2020 312 18 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close