When conduction/diffusion term in the energy and mass conversation equation can be neglected?

09 September 2016 0 3K Report

what is the value of Peclet number at which diffusion term in the energy and mass conservation equations can be neglected.

Badges
Science topic

More A.M. Alatyar's questions See All

How to select between Laminar and Turbulent viscous model in FLUENT?

Some problems are fully laminar and the other initiate as laminar and establish as turbulent flow. Other problems are turbulent with lower Reynolds number than Critical Reynolds number such as...

06 July 2016 3,315 6 View

Moving wall, frame motion ,mesh motion

In FLUENT, What is the difference between moving wall, frame motion ,mesh motion .Do these give the same simulating result for wind turbine.

06 July 2016 11,014 1 View

Achieving the steady state conditions ?

If I want to study the performance of plate heat exchanger,I should take my temperature recordings during the steady state operation. How can I know that I reached the steady state conditions. Can...

05 June 2016 3,299 8 View

Increasing the effectiveness of plate heat exchanger without corrugations ?

Is there any other geometry enhancement that can increase the effectiveness of plate heat exchanger rather than corrugations. Some modifications can applied during manufacturing the plates. This...

04 May 2016 7,678 8 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View