About transparent ceramics?

thank you 1. Why uniformity of grains is important to have transparent ceramics?and How is effect uniformity of grains on increasing transparency of ceramics?then What can we do for have final...

01 February 2017 7,199 0 View

Why we need to cubic structure to produce transparent ceramic? and Is cubic structure concern to grain shape or unit cell?

if that is related to grain shape Why in some source implied "a lot of transparent have cubic structure but in some articles produce transparent ceramic with monoclinic or hexagonal structure is...

31 December 2016 9,062 3 View

Hi, How can we compeletely define synthesis ?

tnx

10 November 2016 6,791 0 View

Hello , How many roues are there for chemical synthesis ?

thank u

10 November 2016 5,403 0 View

I will used solid state reaction (SSR) for synthesis ZnWO4 , is it important the particles starting soluble in solvant?

09 October 2016 603 3 View

Is it any different between ceramic and polycrystal ?

tnx

09 October 2016 241 0 View

Is there valid sources for solubility material in solvants (especially water and ethanol) ?

09 October 2016 3,256 2 View

Who can introduce to me a software for calculate melting point a composition with some impurities ?

tank you

07 August 2016 9,495 1 View

Are there any different between soak time and dwell time in sintering processe ?

tnx

04 May 2016 6,365 0 View

Do we have any metallic scintillator ?

tnx

04 May 2016 5,252 0 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View