About transparent ceramics?

thank you 1. Why uniformity of grains is important to have transparent ceramics?and How is effect uniformity of grains on increasing transparency of ceramics?then What can we do for have final...

01 February 2017 7,199 0 View

Why we need to cubic structure to produce transparent ceramic? and Is cubic structure concern to grain shape or unit cell?

if that is related to grain shape Why in some source implied "a lot of transparent have cubic structure but in some articles produce transparent ceramic with monoclinic or hexagonal structure is...

31 December 2016 9,062 3 View

Hi, How can we compeletely define synthesis ?

tnx

10 November 2016 6,791 0 View

Hello , How many roues are there for chemical synthesis ?

thank u

10 November 2016 5,403 0 View

I will used solid state reaction (SSR) for synthesis ZnWO4 , is it important the particles starting soluble in solvant?

09 October 2016 603 3 View

Is there valid sources for solubility material in solvants (especially water and ethanol) ?

09 October 2016 3,256 2 View

Who can introduce to me a software for calculate melting point a composition with some impurities ?

tank you

07 August 2016 9,495 1 View

Are there any different between soak time and dwell time in sintering processe ?

tnx

04 May 2016 6,365 0 View

Do we have any metallic scintillator ?

tnx

04 May 2016 5,252 0 View

Packing factor for Bcc structure can calculated and its value is 0.68 , Is it for what ?

04 May 2016 5,368 0 View

What is difference between In-line transmission (%) and Total transmission (%) value of optically transparent Ceramics?

I am working on transparent/translucent zirconia-based ceramics. In many papers, I have seen that they are reporting both In-line transmission (%) & Total transmission (%) value of...

20 February 2021 9,405 6 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

Sample preparation for ceramics i.e. iron silicate (fayalite), iron oxides, alumina, spinel mineral (hercynite)?

Recommendations in preparing ceramics for nanoindentation and in the process minimize introducing stresses from sample preparation i.e. polishing stage.

02 February 2021 6,211 3 View

What should I do if the reviewer couldn't finalize the review in the journal's given time?

I have Submitted 2,3 Papers in Science Direct associated Journals but the time of the first decision has been ended so What should I do? Could I email them to remind them about the first decision?

01 February 2021 5,788 7 View

What are the thermodynamic and kinetic similarities and differences among dendrite formation during solidification of metals, ceramics and polymers?

Basic dendrite formation of metallic alloys are explained by thermal and constitutional degree of supercooling and most-supercooled band of liquid somewhat ahead of solidification front that...

30 January 2021 8,450 2 View

Control in microstructure with growth inhibitor?

Dear researchers, I wish to understand the role of grain growth inhibitor in controlling the microstructure of the ceramic pellet. How it controls the growth? Also, I wish to know the grain...

15 January 2021 3,859 3 View

How can I select the concentration of test sample for MTT assay?

I synthesize a powder composite include two ceramics and a polymer coating. I want to do MTT test and I'm not sure about the concentration of powder dissolve in DMEM media. Shall I start with a...

10 January 2021 9,984 1 View

How to choose proper spindle for measurement of thixotropic behavior of ceramic slurry?

Hello, we are studying on thixotropic behavior of ceramic slurry . We will perform the thixotropic behavior analysis of ceramic slurry with the density of 1,7 g/ml by using BROOKFIELD DV2T. How to...

08 January 2021 1,776 5 View

Hi, could anyone help me knowing which kind of Diamond blade would be better to cut thermoplastic composite?

The blade that could cut ceramics, or the one that could cut plastics and polymers?

06 January 2021 2,713 3 View

Which type of press is proper and common for making PZT parts?

What kind of press is using to make electroceramic parts, including PZT parts (hydraulic press, pneumatic press, etc.)? Furthermore, what is the reason for using this type of press? And does the...

28 December 2020 1,215 2 View