What's the value of S11, S12, and S44 for cubic crystals of magnetite nanoaprticles?

09 August 2023 0 224 Report

Greetings,

Recently, I synthesized magnetite (Fe3O4) nanoparticles, and I want to find out the Youngs modulus as well as uniform stress deformation mode (USDM). To calculate those, I need the values for S11, S12, and S44. Can anyone provide any suitable references for those values?

TIA

Badges
Science topic

Similar topics
Chemistry

More A F M Fahad Halim's questions See All

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

How can I homogenize this data to make a meta-analysis?

Hi, I am doing a review and hopefully meta-analysis for my Master thesis but I have the following problems: - Some studies only give the difference between end trial and baseline data and other...

22 February 2021 1,115 4 View

Research Gate Does it help researches to publicize their scientific work ?

In my opinion, the RG site is useful in solving scientific problems and shows the researcher's ability. Besides, the separation of the H-index from the self-citations and the overall index is an...

22 February 2021 3,894 6 View

Monte Carlo simulation?

Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...

22 February 2021 3,680 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Is it possible to obtain a negative cronbach alpha?

Good evening everyone. If a questionnaire has 4 factors measuring different constructs as for example CAMI questionnaire measuring attitudes toward the mentally ill that has four factors:...

18 February 2021 3,223 3 View

Is There are any idea to achieve H NMR signals for swollen compound ??

the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please

16 February 2021 8,801 3 View

How many samples can be pooled together for NGS?

We collected faecal samples from various species that we want to analyse their microbial communities' DNA via Next-Generation Sequencing. The problem is that due to budgetary constraints, we will...

16 February 2021 5,466 4 View

What is the difference between the XRD patterns?

These are the XRD patterns for the same sample, but they seem different; one of them has broader peaks than the another, and when I count the size of the crystals using Scherrer equation, the...

11 February 2021 5,477 4 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Build an orthogonal box in ASE?

Hello, I was wondering the best way to build an orthogonal box filled with a defined crystal structure in ASE. I know it could be easily done in LAMMPS, but I guess it is also doable in ASE. The...

21 February 2021 5,899 4 View

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View