Phytic acid limits bioavailability of micronutrients: Is challenge for biofortification?

As many researcher have confirmed that phytic acid content basically present in cereals and legumes crop that responsible for limiting bioavailability of micronutrients (Fe and Zn) in seeds. Lets...

31 January 2021 5,556 8 View

Can a compound have LogP value around 0.05 and LogD value around 4.02?

I understand that there might be huge differences between LogD and LogP for ionizable compounds. Normally, logD should be lower than logP for ionizable compounds. But can LogD value be...

05 January 2021 6,714 0 View

Biofilm Biofertilizers- New Generation biofertilizers?

Biofilm Biofertilizers-It is being applied to adhere the surface of soil and plant matrix containing consortia of various micro-organism that cut down chemical fertilizer. It is cost effective...

12 October 2020 4,883 13 View

Ethics in research publications?

In present scenario, lots of work were done by researchers and no doubt some of these have potential to change mindset of others that visible through benefiting farmers and other stakeholders....

09 October 2020 4,087 7 View

Can I please get some help with a suitable dissertation topic?

I am a PG student working on my dissertation related to effective document control using BIM. Also looking at alternative topic related to lean construction and BIM Can someone please help find...

14 September 2020 7,153 10 View

How to use commands in ansys workbench?

I am trying to input the material data in ansys mechanical with the help of command i have.This experimental data only consists of stress strain value of concrete cubes.I dont know where this code...

02 August 2020 7,769 5 View

How do I give glucose supplements to rabbits after Alloxan intra-peritoneal dose to prevent hypoglycemic shock?

Its study for alloxan-induced diabetes in the rabbit.

14 July 2020 2,869 1 View

How genetic algorithm can be used to find optimal weights and biases of neural network?

Assume a 3-2-1 (3 neurons in the input layer, 2 neurons in the hidden layer and 1 neuron in the output layer) neural network. How genetic algorithm can be used to find optimal weights and biases...

24 May 2020 1,778 2 View

How to apply displacement boundary condition in ansys?

i have data of compression test conducted on concrete cube of 150*150*150 in form of failure loads. How to calculate the displacement to be applied as a boundary condition in ansys workbench if...

07 May 2020 8,149 4 View

How can I analyze flouride through HPLC ?

How can I analyze flouride through HPLC ? is IC better over HPLC for fluoride analysis or ISE is evergreen? I am Curious to know any better analysis for ionic fluoride which is less time...

28 February 2020 5,129 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View