How to interpret the surface roughness trend in PES/GO membrane?

adding graphene oxide / rGO / graphene have shown conflicting surface roughness changes in Polyethersulfone. for rGO in specific, why do we have roughness decrease whilst porosity has increased?

01 February 2019 9,601 5 View

Does Graphene oxide experience electrophoresis also in NMP ?

GO in NMP - considering NMP is not an electrilyte on itself, can the flakes move towards the opposite electrode?

08 September 2018 9,227 0 View

How to interpret the increase of water contact angle in polymer / graphene oxide ?

when the loadings of GO in the polymer increased the contacact angle was almost the same as the pure polymer and in one case higher... what can be the reason ... it is expected to have more...

04 May 2018 7,944 3 View

Why does my polymer solution tends to stick to the electrode while being imposed to electric field?

when I apply an electric field over my polymer solution it tries to move toward the negative electrode (the distance between the two electrodes is very low) this local movement is different every...

02 March 2018 9,968 4 View

Which side of the membrane is the top side?

while casting a carbon filler /polymer composite membrane on glass, during inversion in water , it gets up with a convex surface which is a little shiny. is this side the top surface of the...

01 February 2018 7,868 9 View

Why water does not reach to the edge of the blade while sectioning in ultramicrotome?

when i want to try thick sectioning of my sample, I fill in the tray with water bu even with angular and axial regulations and also filling and vacuuming water , it does not wet the upper part !...

31 December 2017 6,374 6 View

How to calculate the average viscosity and the dielectric constant of a solution of polymer?

I need to know the viscosity and dielectric of my solution. (polymer in a polar solvent)please advise if there is simple models or estimation techniques just to know an approximate estimation

31 December 2017 5,926 2 View

What are the techniques for adherence improvement between polymer thin film (water soluble ones) and metal surfaces?

I need to cover a metal surface with a thin layer of a water soluble polymer and this layer should adhere very well and not separate , also no-toxic ... what are the feasible methods?please...

31 December 2017 3,620 10 View

Is it possible to use membranes of diameter lower than 5 cm in Sterlitech setup?

my membranes are produced about 4.5 cm . is it possible to test them by a sterlitech HP4750 cell with some modifications of the setup?

11 December 2017 3,742 2 View

How to get more homogeneous membrane while casting ?

when we are using phase inversion method, how can we avoid formation of holes in the film casting on a glass slide? what parameters are effective?

09 October 2017 4,670 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View