I have to perform an accelerated carbonation test on cylindrical mortar samples. I am wondering if anybody knows what sort of epoxy can be used for covering the flat surfaces, so that only the curved surfaces are exposed to CO2.
Thanks Haider for your good suggested articles
I have got a slag sample that contains high amount of iron in it. I conducted xrd using Cu tube, on the powdered sample with very high background (because of iron efflorescence). Then to improve...
05 June 2019 1,766 6 View
Do all iron containing compounds show fluorescence in XRD with copper radiation or just the oxides of iron show this effect? Say for instance if i have pure tetracalcium aluminoferrite (C4AF) or...
05 June 2019 6,804 2 View
I did XRD on anhydrous sodium sulfate salt (purity>99%) which i bought couple of months ago. For some reason sodium sulpfate peaks from PDF database (anhydrous or hydrated) don't align with the...
02 March 2018 6,006 7 View
I submitted a research paper to one of the Elsevier journals and got a response from the editor as below: "The paper has got 23 % similarity in total and from one single paper 10 %. However, if...
02 March 2017 4,220 3 View
Just wondering if anybody has done thermogravimetric analysis on pure hemi and mono carboaluminate phases? I am looking for the mass loss of chemically bound water. Based on the references I have...
11 December 2016 6,064 2 View
I have a slag sample with following elemental oxide composition: CaO, SiO2, Al2O3, MgO, SO3 and also contains carbon (in calcite). I have managed to identify the following phases: Gypsum...
10 November 2016 2,434 10 View
I have a slag sample with following elemental oxide composition:CaO, SiO2, Al2O3, MgO, SO3 and also contains carbonate bearing phase(s). I have identify the following phases in XRD:Gypsum...
10 November 2016 427 3 View
What are the important factors to select chebychev polynomial order for background function in TOPAS. If am checking the degree of crystallinity and I start with modelling the amorphous hump, do I...
10 November 2016 5,925 5 View
I have conducted TGA and XRD of 7 day hydrated sample containing cement, fly ash and nano silica. The TGA analysis show high amount of mass loss with an endothermic TGA peak located at about...
07 August 2016 7,650 6 View
I have a mix design of cement flyash blend. After doing rietveld refinement I have found that the ettringite percentage that was 1.57% at 7 days reduced to 0.85% at 28days. The gypsum content that...
06 July 2016 722 6 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...
04 August 2024 8,997 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...
01 August 2024 8,754 2 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
Hello, I'm involved in a project focused on constructing and maintaining gravel roads in rural areas. We're particularly interested in ensuring durability and reducing maintenance costs over time....
29 July 2024 9,623 0 View