I am designing a 32 nm fineft, in Dc it is working fine but when I try in AC analysis, I always get "Exit due to failure " error message. I think it is a meshing problem. But what would be the meshing?
I have designed magnetic material with different biasing conditions in HFSS. Now I want to give an RF AC signal and do a transient simulation in HFSS. Is it possible to do in HFSS? Please help me...
24 July 2024 9,319 5 View
why the solubility of chitosan is poor, and how does it affect the grafting process?
22 April 2024 1,207 1 View
Marble mining have been abandoned since 2015 in Lalitpur Municipality of Nepal. Under my thesis, I have decided to check the status of vegetation in the Mine. But, I am not quite confident what...
18 March 2024 1,968 0 View
Explanation: Only 57% of the expenses for urban trains and 40% for suburban trains have been recuperated, a fact that regular train travelers might have observed through ticket prices. Despite...
24 November 2023 5,995 2 View
How best a judgement can be made based on modelling PM10 and PM2.5
15 October 2023 6,552 0 View
Normally for ZnO, ibrav = 4 (i.e hexagonal). Now I want to perform gas sensing studies. So I create a vacuum of 10A in nanolabo where the atoms are placed. The ibrav now changes to 12 (i.e...
12 September 2023 3,180 0 View
Animals are enigmatic beings to us. Their emotions remain a mystery, and their communication methods are beyond our comprehension. However, consider the possibility of an individual who has an...
09 September 2023 4,943 6 View
I am trying to Multi-criteria Analysis for seismic vulnerability assessment where retrofitting done or not is one of the criteria. Here I have assigned 0 for no and 1 for yes response. Similarly...
03 July 2023 305 0 View
I need the steps for calcualting the EML for different frequecny and how to plot it in excel. How do I extract the computed data from comsol and plot it.
29 June 2023 8,504 0 View
I tried to identify plasma metabolites using the Agilent 6550 q-tof system. The spectral hits with the column are not coming as expected and seem similar to the blank run. please suggest some...
28 May 2023 5,551 0 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,177 3 View
Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...
03 August 2024 7,843 1 View
Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...
31 July 2024 5,785 4 View
Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...
30 July 2024 8,339 2 View
Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...
30 July 2024 906 2 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?
29 July 2024 4,955 0 View