What materials and equipment are needed to cover the seeds of rapeseed?

More Aydin Hassanzadeh's questions See All

How can I be sure the new isolate of a fungus is a new report of it?

Hey guys, How can I be sure the new isolate of a fungus is a new report of it? e.g. such as a new place or a new host. e.g. United States Department of Agriculture: the database for fungi:...

31 December 2018 1,827 0 View

What is the best method to assess of enzymes activity of Trichoderma isolates?

I want to assess of enzymes activity of 500 isolates of Trichoderma. I want to identify best isolates of Trichoderma and then I will use it as a biological agent against some of most important...

04 May 2018 7,582 2 View

What are the best specific primers for identification of a lot of Trichoderma isolates at the species level?

I want to identify 100 isolates of Trichoderma. what are the best specific primers for identification of a lot of Trichoderma isolates at the species level?

03 April 2018 2,186 4 View

What is the best method to assess of enzymes activity of Trichoderma isolates?

I want to assess of enzymes activity of 500 isolates of Trichoderma. I want to identify best isolates of Trichoderma and then I will use it as a biological agent against some of most important...

03 April 2018 5,188 9 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

What is the most effective way to sterilize camelina seeds?

I'm working on camelina seed sterilization and have some doubts about the process. I followed a protocol used by my lab mate, but I'm unsure about a couple of things: Is it safe to use 10% bleach...

02 August 2024 1,178 3 View

When should I stop watering A.thaliana for collect their seeds?

I have been following Rivero et al 2014 protocols, but I am not sure when I should stop watering because my plants are completely yellow but the siliques are not 80% brown. Any recommendations?...

30 July 2024 2,301 7 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Best Practices for Constructing and Maintaining Gravel Roads in Rural Areas?

Hello, I'm involved in a project focused on constructing and maintaining gravel roads in rural areas. We're particularly interested in ensuring durability and reducing maintenance costs over time....

29 July 2024 9,623 0 View

Seeking recommendations for equipment to mimic sunlight and heat up a greenhouse system?m?

I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...

28 July 2024 4,006 2 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

Maria Eloísa Salustiano

Aydin Hassanzadeh

I have never worked with rapesseds but I can indicate this reference.

https://core.ac.uk/download/pdf/15435865.pdf

You can ask to author about your questions

Good look!

Thanks alot dear Maria

Saddam H. Cheyed

you can fiend your answer in the attached file

Hi Saddam H. Cheyed

Thanks alot

Best wishes