What is the structure of files file.LDOS and file.RDOS in the TBTRANS run in Siesta ?

More Prabhleen Kaur's questions See All

How to calculate the exchange coupling in a charged radical complex ?

I have a neutral complex with two magnetic centers. For this case it is easy to calculate the exchange coupling as the broken symmetry state is converged properly. But when I am making the complex...

09 October 2018 7,239 1 View

I am getting different answers with all the input (INCAR, POSCAR, POTCAR, KPOINTS)same in VASP ? what could be the issue ?

Two same calculations were run from different accounts in hpc-cluster, each on 2 nodes containing in total 48 cores. But in once case I am getting my calculations complete while in other case it...

31 December 2017 8,036 4 View

What is the difference in input of transiesta scattering region in siesta 3.2 and 4.0.1 ?

I have run transiesta calculations in version 3.2 but when I am trying to run in 4.0.1, the electrode part is running fine but for scattering region it is giving error: "The electrodes are not...

09 October 2017 2,103 2 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How vulnerable is water and wastewater infrastructure to cyber terrorism in an age of IoT?

Im looking for any papers, reports,articles, links etc on information on How vulnerable is water and wastewater infrastructure to cyber terrorism in an age of IoT.

24 February 2021 2,750 4 View

Aadhityan Arivazhagan

Can you upload the model file so that i can tell....

Prabhleen Kaur

@Aadhitiyan Arivazhagan i am uploading files. Please have a look

I guess this is non-fermi corrected.

I mean. I think you have to correct it according to your Fermi level.

I could not able to get which version of siesta you used to produce this file. i suggest you to perform any known system(already done by someone). Then compare your result.

@Aadhityan Arivazhagan version is siesta 3.2. I will try with the known system.

Thank you

tried???

@Prabhleen Kaur use gollum to get the correct plot easily.

Nick Rübner Papior

They are Fermi corrected.

I.e. E - E_F is used.