What is the step should be for cyclic hardening in abaqus?

11 November 2017 1 10K Report

Dear All,

I am trying to build a cyclic hardening model in abaqus. The loading is a stress sinusoidal function Stress=Asin(wt). Which one of the following is the correct 'Step' set up?

(1) Creat Step>General>Static,General,

(2) Creat Step>General>Direct cyclic,

(3) Creat Step> Linear perturbation>Freqency.

It would be great if you can also explain the difference among them.

Thank you.

Manigandan Sekar

SIr, Use step 3 and refer relevant literature for eigen values

Badges
Science topic

Similar topics
Correction

More Zhicheng Wang's questions See All

Why part translate in Y axis without loading in Y axis (Abaqus)?

I want to build a very simple 2-D Planar deformable shell model in Abaqus CAE. Model boundary condition is left-side (u1=ur2=u3=0), with elastic range load on right-side. My Question is why the...

10 November 2017 3,618 3 View

How do we decide the number of back stresses of a nonlinear kinematic/isotropic hardening in ABAQUS?

We can choose one or two back stresses when we set up the nonlinear kinematic/isotropic hardening in ABAQUS. How do we decide the number of back stresses? let say model under uniaxial or...

09 October 2017 6,823 3 View

As we all know, Sr can modify Si particle size and morphology in Al-Si alloy. What can be used to modify CuAl2 phase in Al-Cu alloy?

05 June 2017 9,552 2 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View