Standardized test methods exist for liquids and gases, but testing solid materials, such as rubber compounds, presents unique challenges.
I have my RNA samples eluted in nuclease-free water. But now I want to store it for a longer period. Can I add isopropanol directly to my samples to store it without doing a second round of TriZol...
23 June 2024 2,576 4 View
I want to know about water contact angle of silica films without using any surfactants.
29 May 2024 4,526 3 View
supercapacitor application
13 May 2024 5,612 1 View
I was not very familiar with material studio software. I have run the DOS calculation, but I can not find the Fermi energy in the DOS output file. I have to do the Fermi energy level correction...
20 April 2024 8,223 0 View
While conducting experiment following data were obtained Compressor inlet pressure : 120kPa Compressor inlet temperature: 29°C Compressor outlet temp:1000kPa Compressor outlet temperature: 66°C
07 April 2024 3,045 4 View
I am trying to purify this eukaryotic protein (mol wt 60 kDa) in Rosetta strain. It is getting expressed in good quantity. However, there is another stubborn host protein (mol wt around 70 kDa)...
01 April 2024 3,961 3 View
Hi. I had written a manuscript on Bibliometric Analysis related to oral cancer last year. Since then I had sent it to multiple journals only to get rejected. I request you all to please give me...
04 March 2024 2,924 5 View
I along with my friends have been doing experimental analysis on VCRs by adding heat before and after compressor for our fourth year project. We have been observing that COP of our system is...
20 February 2024 6,133 1 View
I want to analyze degradation intermediates of phenolic compound through GC-MS analysis which I had carried out in aqueous solution. For liq-liq extraction of phenolic compound from aqueous...
25 December 2023 1,205 4 View
I have synthesized cDNA using one microgram RNA template. Then, I diluted it to five times. Then, I did PCR using diluted cDNA with housekeeping gene act2. In PCR, I got nice bands in the gel....
27 September 2023 8,098 4 View
Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...
24 July 2024 5,908 0 View
In 2018 the OHSAS 18001 was improved and progressed into ISO 45001. This was characterized by one or two short falls. I am now reviewing the ISO 45001, with the aim of looking at the entire...
18 July 2024 9,489 0 View
Requirement for compliance with ISO 1702
13 July 2024 3,918 0 View
Polymeric film such as latex rubber substrate or polymer
01 July 2024 8,343 4 View
When polyethylene, whether high-density or low-density, is mixed with percentages of waste tire rubber, it becomes a new material. Where can it be used?
26 June 2024 3,349 2 View
I have a copolymer if epoxy and rubber reinforced with Sic. I want a standard FTIR figure in transmittance mode.
20 June 2024 6,606 2 View
I am trying to define the viscoelastic parameters of a rubber material using abaqus, but I don't quite understand how to proceed. I now have stress-strain curves at different temperatures, and...
13 June 2024 3,150 2 View
Could you provide me with the ISO protocol for measuring nitrites and nitrates in soil?"
25 May 2024 252 0 View
Compound composition : EPDM, Oil, white fillers, sulfur, accelerator, activator, blowing agent, retarder...
21 May 2024 2,967 0 View
CIR 2021/808 written as "the CCα shall be calculated as follows: Method 1: by the calibration curve procedure according to ISO 11843-1:1997 ( 14) (here referred to as critical value of the net...
13 May 2024 9,481 0 View