Best plasmid could be used as a standard curve for AAV titration?

I have been trying to have a good AAV titration for my production and I have tried different plasmids to set up as a standard curve but each one behaves differently. i am trying to use ITR for...

23 February 2021 5,167 3 View

Pls inform me if the problem here is in the used red safe. im using the red safe of vivantis co, Malysia. using 5 microliter per 100 ml of agarose?

Why the ladder is always with so closle or attached bands after the 500 bp band whatever i use a type of ladder ( 5types) and also the PCR product is bended. is this has a relation with the used...

05 January 2021 5,211 5 View

Is it important/advisable to write a summary for each theme (and subthemes) in Thematic Analysis?

I am conducting semi-structured interviews with graduate students to explore their academic writing challenges. I am using thematic analysis to analyze the Qual findings. Should I include a...

31 December 2020 3,593 22 View

Using Matlab and the analytical solution for Room acoustic modeshapes, is it possible to plot modes in 3D?

mode shapes similar to attached image.

27 November 2020 4,262 7 View

What tool can I use for creating a Quantative Trait Loci map from SSR data?

I have SSR data for some individual of three hybride How I construct QTL mapping of yield according to these data ?

02 October 2020 502 5 View

Labs for purification, identification & isolation of unknown proteins form native sample of honey and to test versus GS-9L cells in vitro?

I asked for protein purification, identification and isolation of unknown proteins and test versus GS-9L other than that we already got in our patent WO/2014/040605 - form native sample of honey?!

23 September 2020 1,839 3 View

Hi everyone, do you know any GPS logger that we can use to conduct travel time surveys and which is easy to extract the data from ?

We are currently planning to conduct Freight Master Plan in the state of Qatar, one of the requirements is to conduct travel time surveys, therefore we are currently searching for GPS devices that...

22 July 2020 1,889 1 View

How can I quantitatively analyze a sample with carbohydrate content?

Can anyone -who may have hands-on experience in analytical chemistry or photochemistry- help me how can I quantitatively analyze a sample with carbohydrate content?

09 July 2020 3,663 2 View

Any Predictive Markers for Severe COVID-19 in children?

Predictive Markers for Severe COVID-19 Identified

15 June 2020 1,375 5 View

How to critize (Evidence based medicine) this paper?

24 May 2020 5,489 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View