What is the reason for the slight difference between periods in structural modeling in SAP and Opensees software?

28 May 2021 0 3K Report

I modeled a 5-story frame with 3 bays in these two softwares, and periods 1.15 and 1.09 sec were obtained in SAP and Opensees, respectively.(The period of the first mode of the structure)

Badges
Science topic

More Sahar Ebrahimi's questions See All

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

When making abraxane with Nab tech, why is 9:1 Chloroform&EtOH used as solvents?

Is it the best optimization ratio based on experiments?

22 July 2024 8,170 0 View

Can diamond be grown using molecular beam epitaxy?

22 July 2024 9,755 2 View

How can I use LabVIEW to control of an ethernet-based driver?

Hello everyone, I am new to LabVIEW, right now we need to control the movement of an ethernet-based stage drive. We got the sample code from a collaborator but their instrument is USB-based, so we...

11 July 2024 5,385 2 View

Systematic review meta-analysis paper?

Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...

10 July 2024 5,490 5 View

Do the SHSY5Y cells tend to form multiple layers over each other when highly confluent?

I have attached pics of the SH-SY5Y cells within a seeded plate after reaching >80-90% confluence. Are these dark clumps of multiple growing cell layers? Or dead cells? Any clue? many thanks.

01 July 2024 8,361 3 View

Adding isopropanol directly to eluted RNA samples?

I have my RNA samples eluted in nuclease-free water. But now I want to store it for a longer period. Can I add isopropanol directly to my samples to store it without doing a second round of TriZol...

23 June 2024 2,576 4 View

HI, How to find phase response in CST?

I'm simulating a metamaterial unit cell. I want to plot Frequency Vs Phase Response. Also I want to extract permeability and permittivity. Kindly share the steps.

23 June 2024 3,446 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Using a large amount of data, such as 30 years of daily data, in a machine learning model like LSTM can reduce the model predictivity?

I have used 30 years of daily data, but the model is not able to optimize, getting just 0.57 in NSE and R2. when I reduced the data to 20 years in daily time frame I got 0.73 in NSE, R2 for both...

22 July 2024 669 0 View

How to find out hysteretic energy consumption of the pier after earthquake excitation in sap?

how to observe the hysteretic energy consumption for a parrticular frame element

12 June 2024 3,426 1 View

How can I see the modes of vibrating in a 3D model with opensees?

Hi, I am calculating the periods of a steel building modeled as a 3D moment frame. Is there any script to display the shape of vibrating of the model in opensees?

12 June 2024 8,065 1 View

Adding a frame element into an OpenSees model after running initial?

Hi, I am running an opensees model of a 2-bay 1-storey frame with settlement at the mid-support. I wanted to add an additional frame element as a bracing to the analyzed frame after it sustains...

08 June 2024 4,132 0 View

How to define non-linear parameters for time history direct integration case in SAP2000 using MATLAB API functions?

I use MATLAB to define SAP Model using API function but when trying to define time history direct integration case, the non-linear parameters change from the default which affect the results and...

04 June 2024 2,369 1 View

How can I calculate average dG MM/GBSA energy from selected frames of MD trajectories?

I need to calculate dG MM/GBSA energy through the MD simulation trajectories. From RMSD values I selected last 400 frames from MD trajectories. I ran thermal_mmgbsa.py script, but it calculates dG...

22 May 2024 10,076 5 View

How to express spinors with an arbitrary change of coordinates?

A spinor field in classical differential geometry is defined as a section of a spinor bundle, which is by definition the associated bundle constructed from the spinor representation and the...

14 May 2024 400 0 View

Why do I get frameshift mutants in antibody phage display?

I'm performing an antibody phage display with a VHH library and I consistently get frameshift mutants (mainly frame +2) after biopanning. I'm using TG-1 cells for amplification of phagemids and...

14 May 2024 412 2 View

I want to make a research about deployment of floating offshore wind turbine and i want to study about the locational location with the criteria?

can u suggest research frame work using ahp research method

10 May 2024 6,080 2 View