What is the difference between L1 and L2 regularization in machine learning?

L1 and L2 regularization

28 February 2021 4,187 3 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

Which power-to-heat (P2H) devices do you think are likely to play the most crucial role in the European energy transition?

Power-to-heat (P2H) shows how we can use renewables for heating. Power-to-heat technologies have been on the market for quite some time now, with heat pumps being the most important. However, they...

10 February 2021 9,250 2 View

Why we use feature normalization before using the Gaussian kernel in SVM?

Support vector machine

09 February 2021 6,405 3 View

How is KNN different from k-means clustering?

machine learning

09 February 2021 8,757 9 View

What is bagging and boosting in Machine Learning?

machine learning

09 February 2021 5,156 3 View

Do the introduced salts (NaOH/ HCl) influence the spectroscopic shifts of the fluorescence excitation-emission matrix?

During the resin (XAD-8) fractionation of wastewater salts (NaOH or HaCl) are used for acid or base elutions/pH adjustments. Since the amount of introduced salt is minimal, so is it required to...

08 February 2021 9,489 2 View

Do you think it is feasible to have a 100% Renewable Energy-based Electricity System in Bangladesh in the distant future?

In Bangladesh, the proved reserved of natural gas 34 TCF which will lead the country next 20 years and currently 82% natural gas consumed in the power sector for power production. Whereas only 3%...

01 February 2021 251 12 View

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

How to apply a voltage sinusoidal/harmonic load in ANSYS APDL?

Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....

13 February 2021 3,261 3 View

FLIM Signal to noise ratio of a time series - can I use dark frames to measure noise?

I am doing an analysis on some FLIM data in the form of time series image stacks. I need their signal-to-noise ratio. Recording starts several picoseconds before the excitation pulse, so no sample...

08 February 2021 7,169 3 View

How to eliminate noise when using a sensor with instrumentation amplifier and giving it's output to Arduino?

When I am trying to implement a pressure sensor through instrumentation amplifier and then giving it's output to Arduino, I am getting garbage value due to noise, so how to eliminate it.

05 February 2021 8,598 11 View

Silane solution and application to Glass ?

30 January 2021 7,924 3 View