What is the maximum force that can be applied by a human hand on a hammer in the blacksmith industry?
It can't be limited without assessing factors
Industry allows 40kg load max from worker.
Maximum weight is 25-30 kgs for a worker and may be additional 5 kgs vary in different cases.
pressure of a worker is max 51 pounds.
I have the following equation, Eating choice (Yes/No)~ Box type (A/B/C). So the question is whether a certain box type affects eating choice in groups of dogs. The eating choice of each member in...
10 February 2021 6,024 9 View
what kind of test can I do for testing the level of knowledge about their daily operation?
03 February 2021 7,583 10 View
The observed bandgaps are 3.8 eV and 3.4 eV for spin-coated and electrospun films, respectively. What are the possible reasons?
08 January 2021 5,646 6 View
I want to know the reaction mechanism of monoethanol amine used as flocculating agent for rerefining used lubricating oil. Here I have attached one research paper where MEA (monoethanolamine) is...
01 January 2021 5,681 2 View
18 December 2020 4,559 6 View
I am a junior research fellow in the department of Chemical Engineering, Nit Durgapur. I want to know that how can I determine various metal such as Fe, Cr, Mg, Mn, Pb concentration present in...
15 December 2020 9,887 3 View
In O 1s spectra, usually the peak near 531 eV belongs to oxygen vacancy sites in oxides, however, in silicates, these peaks are often reported to originate from O-Si. I am confused if the intense...
10 December 2020 9,496 2 View
Hi, I am trying to find out the mol. weight of GFP 11 because it is tagged to my protein of interest which is 17kDa. GFP 11 has been tagged with my protein of interest while GFP 1-10 is tagged...
09 December 2020 1,863 1 View
I have Fluorescent Polystyrene beads. I need to graft PEG on the surface of it. I am looking for a protocol to do that. Also need to know which experiment to perform to be sure about the grating.
01 December 2020 7,860 1 View
I am conducting a regression discontinuity design where the dependent variable is continuous while control variables are categorical (except the treatment variable). In the usual regression...
01 December 2020 583 3 View
As the organizations getting prepared for the fourth industrial revolution, to enhance the skills of their workforce what type of changes are necessary and going to occur in the training and...
01 March 2021 3,199 3 View
Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...
01 March 2021 8,747 4 View
The on-going Covid-19 pandemic has had devastating economic effects on many industries. However, few have suffered to the same extent as full-service restaurants. Numerous studies have shown that...
24 February 2021 9,496 4 View
I am helping a local home industry for developing frozen fries from their local farm. I want to know what is the optimum blanching and pre-frying temperature and time for processing. Please also...
23 February 2021 1,616 5 View
I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...
23 February 2021 711 3 View
Related work experience plays a vital role in motivating the Entrepreneurship. But when we talk about high tech entrepreneurship in Aviation industry, we talk about very high investment and high...
22 February 2021 376 5 View
I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...
21 February 2021 7,128 3 View
I have a cellulose model system that is best described by the GLYCAM06 force field according to the literature. However, the set of force fields included in the GROMACS package doesn't include the...
20 February 2021 3,309 3 View
The protein I want to simulate has multiple heavy metals. I wanted to know which force-field I should use with GROMACS to achieve this. Most importantly, do the latest updates in the force-field...
16 February 2021 2,420 1 View
I have been reading this paper Soft Matter, 2017, 13, 1904 and in this paper, they simulate benzene in GROMACS using CHARMM. They mention that they performed simulations of benzene using the...
15 February 2021 5,561 3 View