What is the Fraction of Strain Energy converted to heat during Friction Stir Welding?

02 November 2021 1 251 Report

What is contribution of friction to the heat and what is the contribution of strain energy to heat in FSW of Aluminum Alloys

Anoop N N

You could put it this way instead.. what is the contribution of plastic deformation to heat... strain leads to hardening the material...

Badges
Science topic

More Venkata Somi Reddy Janga's questions See All

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

Can a luenberger observer (even a modified version) be effective for a nonlinear affine system?

I want to know whether a luenberger observer or a modified form of it be effective for estimating the states of a system of the following forms: 1. x_dot = f(x,u,d); y = x 2. x_dot = f(x,u); y =...

20 December 2020 1,392 4 View

Is there any software for calculating hit bias (HB), missed precipitation (MP), and false precipitation (FP)?

I have a time series of two rainfall products. For error decomposition analysis, I have to calculate HB, MB and FB. Is there any software for calculating these variables.

27 November 2020 980 2 View

I'm looking for cell culture models for Alzheimer's by targeting amyloid beta peptide, tau protein, bace 1 enzyme ; can anyone give me details please?

I want to target particular protein/peptide/enzyme by cell culture methods. I would also like to know screening methods for cell cultures to analyse and diagnose the drug effect on particular...

24 November 2020 7,255 5 View

Can someone help me in designing off-MPPT mode in a Standalone DC Microgrid?

I am working on voltage control of a Standalone DC Microgrid consisting of Single PV source, a battery and loads. The PV is interfaced through Buck converter to the DC bus, the battery is...

01 October 2020 7,071 2 View

How to scale the time frame of battery operation in MATLAB?

How can we make the rating of a battery in MATLAB/Simulink to Amp-sec instead of Amp-hour? I have tried with reducing the factor of 3600 to 1 inside the battery block. Is this approach completely...

03 July 2020 4,017 4 View

Why a colorimetric assay is usually not in green?

Various colorimetric assays we use are blue/purple/pink/red but not in green shades. Is there any particular reason for this?

30 May 2020 5,834 1 View

Can someone suggest me a good resource to get the information on design of Adaptive controllers like Model Reference Adaptive Control in MATLAB?

Please suggest me a good source to learn the design of adaptive controllers like MRAC. Resources related to the implementation on MATLAB platform and for Power electronic converter systems would...

01 May 2020 7,422 3 View

What are some physical methods to determine binding affinity of a protein?

What are various options available while determining the binding affinity of a protein to it's target? In my case the target is also a protein. Are there any standard physical methods to...

09 March 2020 8,053 8 View

How to calculate setup time and hold time of a memory circuit in CADENCE Spectre Simulator?

Dear all, How to calculate setup time and hold time of a memory circuit in CADENCE Spectre Simulator?. We have designed Content Addressable Memory (CAM) using 45 nm technology in CADENCE Spectre...

05 January 2020 9,460 3 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View