Hello,
This is a question regarding slurry mixing for use in lithium ion batteries. Is the mixing regime laminar or turbulent when the slurry is prepared?
Can someone also recommend reference literature for this as well?
Mudit
Traditional social structures carried inherent inequality such as caste system in India. It was argued that the market will provide with "just" society. After so many decades of market promotion,...
09 December 2016 4,332 7 View
I am designing a rubber component, which is used for vibration isolation. Vibration levels are varying throughout the frequency (1 to 200Hz). I want to know, which will be the most crucial...
02 October 2016 1,952 3 View
I have to design a rubber damper for a bike to reduce the road vibration. To select the appropriate elastomer material, I have performed a frequency sweep DMA test of two different elastomer...
11 September 2016 4,218 5 View
I am performing a frictional heating test, in which i am rubbing a asbestos material against a cast iron plate. During rubbing action, temperature of plate increases, but after stopping it also...
13 July 2016 1,293 5 View
Please provide personal experiences and literature, if any.
22 May 2014 7,661 4 View
Is intron site prediction reliable?
03 October 2012 369 3 View
This a self annealing result of an upper primer from OLIGO EXPLORER 5'-CATCGCACGTCGTCTTTC-3' : : :
28 February 2012 4,220 15 View
I am using smartPLS version 02 to calculate bootstrapping CIs for outer weights.
01 January 1970 6,525 3 View
There has been increasing use of asset holding as a measurement of economic well-being (Filmer and Pritchet, 2001; Vyas and KumarNayake, 2006; Moser and Felton, 2007). It is argued that it...
01 January 1970 2,258 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
anyone looking for research collaboration on the anaerobic digestion slurry and digestate can contact me for further details. As my whatsapp number is +91 8317585217
11 July 2024 6,753 3 View
I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...
08 July 2024 7,327 4 View
Suppose we have dried MXene slurry (Ti3C2Tx), then the combination of which solvent (in which this dried MXene slurry powder will be mixed, subsequently forming the "ink") and corresponding...
13 June 2024 5,763 0 View
How the slurry is preparing for cathodes in batteries?
13 June 2024 4,314 3 View
I attempted a phosphate (apatite) flotation, but the slurry was too thick for the impeller to work properly. I reduced the solid content to 30% for better mixing, but the conditioning still seems...
14 May 2024 4,505 4 View
If i wanted to make a homogenous coating on a substrate but my raw materials is in powder AND it is 5mg or less (very few). How do I make the final coating? I was thinking of spray coating - but I...
29 April 2024 8,457 3 View
I am trying to prepare high loaded electrodes. Hence, Is it a good idea to coat multiple layers of slurry onto a copper foil to prepare a high loaded electrode? Also, what can be the possible...
26 March 2024 7,208 1 View
For Electrochemical study, slurry is formed to test the material in three-electrode system. Why we need Carbon black for this slurry formation and what it's alternatives?
17 March 2024 1,531 0 View
Tried to use PVDF with NMP and DMF but slurry couldn't be prepared.
15 January 2024 5,790 0 View