What is the effect of CO2 flux on photoreduction of CO2 if flux isn't pure? What impurities could be dangerously converted into hazardous compounds?

07 February 2014 0 8K Report

If the flux is not pure, what impurities can be converted into hazardous compounds during photoreduction of CO2 and thus should be avoided?

More Muhammad Fahad Ehsan's questions See All

Protein-aptamer gel electrophoresis help, please??

Hi, I have problems with running gel electrophoresis. I have tried agarose gel electrophoresis and native PAGE. I have two proteins, which have molecular weights of ~30kDa and ~180kDa and two...

03 March 2021 4,275 4 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Expression cloning by using cDNA,do I need to modify the cDNA first?

I am going to have a expression cloning of mammalian gene by using shuttle plasmid to transforming the E.coli However I don't know I should only inserting the Coding sequence ,or I can...

28 February 2021 5,440 3 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

What are some of the research gaps in machine learning and artificial intelligence in africa?

i would to know some of the research gaps in the artificial intelligence field in most african countries.

03 March 2021 6,145 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

Is there any Machine Learning/AI algorithm that lets you predict with incomplete features without missing value imputation process?

For instance, the model is trained with A,B,C,D,E features to predict F target. Then, I want to make prediction on a new data, but with only A,C,D,E is known without doing missing value imputation...

28 February 2021 1,556 6 View

What are the important topics in the field of Artificial Intelligence in Business world?

Dear All, I am doing my MS in Electronic Businesses. And I am interested in the AI field and its applications for businesses, its benefits, impacts, etc. What kind of scientific research dominate...

26 February 2021 8,816 6 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View