How does SEA software normally number subsystems?

Dear colleagues, What is the common subsystem numbering system in SEA modelling software (i.e. VA One, AutoSEA2)? Cheers, Feng

27 February 2021 7,073 3 View

Can a Golgi-stained dendritic spines picture processed by Image J be directly used for publication?

24 February 2021 3,348 2 View

Why does the fatigue cracks initiate from surface to interior as the stress level decreases?

It is well known that low-cycle and high-cycle fatigue cracks initiate from the surface, while ultra-high cycle fatigue cracks initiate from the inside. I am very curious why this transformation...

17 January 2021 9,633 6 View

How to extract dry soils such as rocks and Debris from Sentinel-2 images using Google Earth Engine?

How to extract dry soils such as rocks and Debris from Sentinel-2 images using Google Earth Engine?

17 December 2020 6,600 2 View

How to understand the chemo-mechanical coupling?

Recently, I came into contact with a new discipline named chemo-mechanical coupling. I found that chemo-mechanical coupling phenomena exist in many research areas, ranging from development of...

17 December 2020 1,065 3 View

I am working on membrane distillation model in COMSOL and I have some problems coming in it?

I need to add a latent heat flux of evaporation to the hot side boundary, which is a function of the pressure difference between the cold side and the hot side boundary.However, the pressure at...

16 December 2020 9,890 1 View

Again, what are the bands of extracted plasmid?

I used Trans1-T1 phage resistant chemically competent cells to extracted lentiviral gRNA expression vectors. And there were bands near 2000bp and smear on 1% argrose gel. Did the smear come from...

25 November 2020 858 2 View

What are the bands of extracted plasmid?

I used MN NucleoBond Xtra Midi to extract plasmids, but the agarose gel electrophoresis showed the plasmids contained not only one component. There are bands around 250bp, what are those bands?

19 November 2020 2,241 3 View

Can I calculate mean and confidence intervals of d-prime values?

Hi everybody. I ran an experiment on memory and calculated the percentage of hits as usually reported in the literature. However, the reviewer asked me to transform my hits into d-prime values. I...

21 October 2020 3,859 1 View

Why does the Abaqus simple tension simulation fail to converge for 2 elements perpendicular to load but not for 2 elements parallel to load?

I am simulating a simple uniaxial tension by pulling for a displacement of 0.4 in the Z-direction on a quarter symmetry cube with side lengths of 0.8. I am using an elastoplastic self-consistent...

08 September 2020 8,937 3 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

Dapi fluorescence protocol for colon cell lines ?

28 February 2021 2,534 2 View

How to design a boost converter for a mppt controller?

I have a doubt on how to select the inductor and capacitor value when I want to implement MPPT controller. This is because we always take a maximum output voltage and current but in this case, we...

28 February 2021 3,637 2 View