What is the correct procedure to balance the e viscous radiator fan. should we balance it with full assembly like fan, drive with visous oil & clutch?

Shunmugasundaram Natarajan @Shunmugasundaram-Natarajan

11 November 2019 1 2K Report

1. How is / should be the balancing of Viscous Fan carried ?

Is balancing of Fan blade & Drive separately to meet final assembly specification a correct method of balancing ?

or it should be balanced in an assembled condition with viscous oil?

K. A. Sharshar

Sorry this question out of the research field

Badges
Science topic

Similar topics
Correction

More Shunmugasundaram Natarajan's questions See All

What is the difference between Hex Dominant and Cut Cell Meshing methods in CFD?

Though both the methods look similar I believe there may be differences in them. What are the disadvantages of cut-cell meshing method and why is not widely used in research in comparison with...

12 July 2020 5,636 3 View

Is SIMSCALE software a good to go option for visualizing and understanding academic concepts?

On what scale can SIMSCALE simulation software be helpful for students in their engineering course work comprising CFD ( Computational fluid dynamics ), thermal and structural concepts? Can...

29 March 2020 2,952 3 View

How is the processive enzyme which ratchets DNA through a (oxford) nanopore attached the "right way about" to the nanopore?

I am curious about how the ratcheting of a DNA strand through a nanopore works in (oxford) nanopore sequencing. I think that the enzyme motor is first attached to one end of the DNA strand to be...

30 August 2018 7,786 1 View

What are the purification techniques available for water purification other than UV and RO system?

I need low cost water purification technique with readily available material for designing solar water heater cum purifier for rural households.

22 December 2017 864 2 View

Problem with DNA standard optamization?

I am preparing DNA standard curve using gag cloned plasmid by SYBR green assay. I have optimized my primers concentration (250nM) and prepared different DNA concentration based on the copy number....

29 August 2017 1,553 2 View

In scan rate study (sensor), why the diffusion controlled process shows negative intercept and adsorption controlled process shows positive intercept?

Because, I am getting negative intercept for my dopamine sensor (diffusion controlled process). When i am plotting the peak current vs square root of scan rate, i am getting negative intercept....

16 April 2017 2,200 3 View

Is there any way to find if my splice mutation has caused an alternative splice site .?

Although i have the cDNA sequence by RT- PCR..how do i still prove the alternative splicing

10 March 2017 8,262 3 View

Weather 3 wheels or 4 wheels are most suitable for hybrid electric vehicles?

what are the flexibility/importance of wheel selection in hybrid electric vehicle.

25 January 2017 4,768 2 View

Formulation of marine microalgae medium using commercial fertilizer/chemicals?

naturally seawater contains lot of nutrients, however I want to formulate my own commercial medium for my own marine microalgae isolate to grow in open pond/photobioreactors (Nannochloropsis sp),...

11 September 2016 4,302 3 View

How can I perform Transwell assay using suspension cell line?

I am studying interaction of HIV and E.coli. For this I want to perform transwell assay and check how interaction occur between both. Can anyone guide me with the protocol used for suspension...

08 September 2016 5,738 2 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

Could the "incoming radiation (net radiation)" values be negative?

Could the "incoming solar radiation" values be negative? What is the difference between "global solar radiation" and "incoming solar radiation"? Which one might be measured negative values?

21 February 2021 7,726 9 View

In methylene blue test Why is UV absorbance reading very low as soon adsorbent is added and then increasing before reaching equilibrium?

Hello, I'm working on removal of methylene blue. 01. in the dark test very first reading is taken 15 minutes after adding adsorbent to the dye solution and that UV absorbance reading is very...

19 February 2021 472 5 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View