What is the best software to be used to analyze the Underwater WSN?

More M. Shamim Kaiser's questions See All

How to process data in real time?

How to prepare big data in real time

01 February 2017 7,147 0 View

Suggest some crosslayer routing protocol for Underwater WSN

Algorithm and QoS issues

08 September 2014 8,153 0 View

How to simulate outage capacity of UWWSN

PDF of UWWSN

08 September 2014 8,210 0 View

What are the main challenges of Underwater Cognetive WSN

BER and Data Rate

08 September 2014 3,897 0 View

Does anyone have the Matlab code of Underwater WSN?

I would like to simulate OFDM based multihop network for underwater.

07 August 2014 3,360 8 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

El-Sayed Mahmoud El-Rabaie

I enclose for you a paper that include more details about the available software for underwater WSN and their merits.

Good Luck

Prof. S. EL-Rabaie

Adnan Nadeem

Dear Shamim

Matlab , recently you will find code of underwater MAC protocol tested in matlab.

Dr Adnan

Mamoun Qasem

I think OPNET, MATLAB and Bellhop ray tracing tool are good options.

check this link:

www.mdpi.com/1424-8220/12/2/1312/pdf.

Best

Surjit Paul

NS3 may be a better solution because it ope source.

Other simulation tools are qualnet, omnet++

Nusrat Zenia

Aqua sim, sunset, UWSim have special features to model underwater channels, All of them works based on NS2

M. Shamim Kaiser

@Sujit is NS3 more user friendly than NS2?

Thanks a lot for the suggestions. It's really nice to learn from all of you.