What is the best model to capture Query passing/tossing in CQA?

07 September 2013 0 120 Report

CQA is Community Query Answering, example stackoverflow.com or Yahoo answers. The current model that is used to capture this query passing is the Markov model. Is there any other alternative to the Markov model?

More Akila Gopu's questions See All

Please, anyone can get me this following book?

Surface Plasmon Resonance Imaging Basic Theory and Practical Methodology

16 May 2024 3,566 0 View

Lithium ion battery Equivalent circuit parameter estimation?

I tried parameterizing an ECM model with an EIS experimental data set using Matlab lsqcurvefit solver. The resulting EIS is in an acceptable range if you see the attached figures. But my doubt...

27 March 2024 4,292 0 View

What is the refractive index for antimone and how we find this?

optical property, particularly for 1550nm

26 March 2024 1,107 3 View

EIS behaviour for different charge rates for Lithium ion battery DFN model ?

Hello Everyone, I am obtaining the EIS from the DFN model and the EIS profile is shifting to the right side when we increase the charge C rate from 0.3 to 1C or 3C (refer to the figure below)....

05 January 2024 8,808 2 View

How do we calculate the complex refractive index of the material?

the complex refractive index having the real and imaginary part of dielectric constant.

21 December 2023 2,018 3 View

How we start programming in matlab for surface plasmon resonance?

SPR

11 December 2023 3,727 3 View

What happen when the frequency is less than plasma frequency?

In surface plasmon resonance

08 December 2023 3,582 0 View

What is a role of Holes in surface plasmon resonance?

interms of Holes

22 November 2023 5,968 1 View

Why the surface plasmon wave decay faster in metal?

19 November 2023 9,531 3 View

In surface we use TM mode can't use TE mode , can you explain briefly ,I can't visualize it?

TEM MODES

15 November 2023 1,457 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Is there a problem with my RNA pellet?

Hello, I am currently having problems with RNA extraction. I am using mouse liver (C57BL6J), and I have extracted RNA from mouse liver before. Before this experiment, my final RNA pellets were...

11 August 2024 7,082 3 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

RNA Extraction Using Hot Borate Method No Longer Working?

I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...

08 August 2024 9,882 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Do you know best mines of western part of Afghanistan?

I want to know more about Mn deposits in west of Afghanistan.

07 August 2024 3,427 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View