I'm trying to cold-press tungsten to a dog-bone sample, can I get a recommendation of a binder that works well for W-powder. Thanks
Perhaps, you could try a wax binder that is derived from paraffin or polyethylene glycol. You might want to check further to see if this suits your purpose.
You should also go through this article maybe you can get further guidance: Article Microstructural modifications of polyethylene glycol powder ...
Respected Sir,
For cold pressing you can use below mentioned binders:
1. Polyvinyl Alcohol (PVA)
2. Stearic Acid
3. Zinc Stearate
4. Polyethylene Glycol
Hope this information is useful.
In a topology optimization machine learning prediction algorithm, can I consider the OOB score of RF as the same as R^2 score. Could that be a more unbiased way of validating the model
14 February 2021 3,540 1 View
I want to perform a simulation study to examine the consistency property of parameters of a new distribution through the quantile function. The simulation study will contain many replicates (say...
10 February 2021 180 3 View
Is there any recent work available on the performance of P2P Lending in India?
05 January 2021 5,211 3 View
I am working to improve a manuscript and I have been advised to provide a map showing where the correlation is significant. Any information or links to learn about this would be quite helpful....
26 December 2020 1,162 5 View
Recently I am getting low performance (PCE and FF) and weird J-V curves on Pb-Sn-based perovskite solar cells. I have been trying to solve this for a couple of weeks now. I will like any...
19 December 2020 9,336 4 View
Water is a molecule that has a very high boiling point compared to ethanol. Why does water have such a high boiling point compared to a molecule like ethanol, and what are the...
23 November 2020 9,662 8 View
I am looking for a website of blog where i can get details about the relevant datasets used for question answering in the medical field. What i found, are not explaining in details these...
10 November 2020 7,202 3 View
I have two XRD data (before and after treatment). I observed peaks shift to lower diffraction which tells me that the crystal lattice expansion occurs. How can I calculate the lattice parameter...
09 November 2020 3,550 5 View
Can anyone guide me to some recent studies on Impact of Microfinance in India on Poverty, Employment and Incremental Income. Many Thanks.
09 October 2020 9,962 1 View
What Economic Activities taken up with Microfinance loans can yield returns greater than 25% which is the usual cost of a micro loan in India?
09 October 2020 3,777 5 View
Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...
03 March 2021 6,223 5 View
Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...
01 March 2021 2,027 2 View
As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...
23 February 2021 3,175 3 View
I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...
22 February 2021 10,099 5 View
My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...
22 February 2021 2,965 4 View
I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.
21 February 2021 8,947 3 View
Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...
17 February 2021 1,709 3 View
Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...
15 February 2021 6,749 2 View
I am doing ball milling operation of Aluminum and silicon carbide powder. I am pretty confused about what should be added as process control agent ? what is role of toluene as PCA and stearic...
12 February 2021 5,205 3 View
I am working with a material which is sensible to water and oxygen, I would like to oxidize this powder either chemical or electromagnetically. Does anyone knows a method to electrochemically...
09 February 2021 2,944 3 View