What is the best annealing temperature for the thin films of ZnO deposited by dip coating technique?

More Abdelkader Hafdallah's questions See All

How is the impact factor of a scientific journal calculated?

07 August 2019 5,217 6 View

How is the impact factor of a scientific journal calculated?

08 September 2018 2,722 2 View

How does droplet affect the growth rate of the thin film in pyrolysis spray technique?

03 April 2018 4,722 5 View

What is the difference between a thin film of ZnO deposited on ITO substrate and FTO Substrate?

what is the difference between a thin film of ZnO deposited on ITO substrate and FTO Substrate

31 December 2017 9,103 7 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

Omar M S

Answer from Braun is recommended

However annealing temperature for thin film is a function of its thickness and in general dependent also on doping elements type

Abdelkader Hafdallah

Dear researchers

thank you for your reply

Muhammad Tariq

Answer from Braun is recommended...

Usually, I use 60-100 oC for 1 cm thickness of Ti plates...

Think you Dr. Muhammad Tariq