Where can I find coordinates of specific regions of interest (ROI) in the human brain?

Hi All, I need to specify a few Regions of Interest (ROI) in the human brain providing their coordinates (x,y,z). What I am interested in at this point are anterior cingulate cortex, dorsolateral...

01 November 2020 8,442 7 View

How can I compare 3 independent variables, of which one should be weighted in linear regression?

Hello, I would like to find create a model and run linear regression with 3 independent variables. However, one of them should be weighted by another variable from my data. SPSS does WLS Weight,...

08 March 2020 6,081 3 View

How to calculate the catalyst volume ?

Hello, With my colleagues we are working on a project. We are currently designing a reactor, for the reaction isopropanol -> acetone + H2 For that reaction a catalyst is needed, and we do not...

19 February 2019 7,173 9 View

Will mammary adenocarcinoma cell line from a Fischer 344 (F344) rat form a solid tumor in any F344 rat after subcutaneous administration?

Will 13762 MAT B III cells (ATCC CRL-1666; mammary gland adenocarcinoma cell line obtained from a Fischer 344 rat) grow efficaciously in any syngeneic (F344) rat and form a solid tumor after...

01 March 2015 3,137 2 View

Large collection of disease-specific case reports versus the population... Do they approximate each other?

I realize this question may sound weird (to say the least)... but I was always wondering if one took all the reported literature cases for a specific disorder / disease (assuming that there would...

26 February 2015 5,483 9 View

Anyone aware of fast DPGMM implementation?

01 January 1970 7,388 2 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

Possible reasons for high bioavailability after I.M and S.C. routes...?

What should be the possible reasons if we obtained more than 100% bioavailability of antibiotics (marbofloxacin) after I.M. and S.C. routes of administration in cattle species.

16 February 2021 971 4 View

How to calculate the sample size required to detect the difference in pharmacokinetics of methotrexate?

I came across with this study here, https://www.clinexprheumatol.org/abstract.asp?a=5066 And this study says: "The sample size calculation was done to compare two different MTX starting dose...

14 February 2021 3,017 3 View

Should the AUC in a concentration-time graph of a subcutaneous implant be roughly the same for poeple?

I have 2 concentration time curves of a subcut drug implant. the first group has a peak around the 50 day mark where as the second group does not. Both groups received the same implant by the same...

10 February 2021 2,305 3 View

Phytic acid limits bioavailability of micronutrients: Is challenge for biofortification?

As many researcher have confirmed that phytic acid content basically present in cereals and legumes crop that responsible for limiting bioavailability of micronutrients (Fe and Zn) in seeds. Lets...

31 January 2021 5,556 8 View

Will rat colon cancer cells (DHD/K12) derived from BDIX rats grow in Sprague Dawley ?

we plan to induce colon cancer by injection. Cell lines derive from BDIX rats, but our experimental setting would favour SD rats. any experience?

23 January 2021 1,437 2 View

Is there a study on the maximum thumb extension that can be possible in a range of population while using injectors?

In Most pen injectors while dialing the dose, the dose dialer comes our or extends outside the pen as dialing happens. How much maximum extension of dialer is acceptable for performing...

17 January 2021 9,770 1 View

How to couple Moldex 3D with MATLAB for design optimization of an injection mould?

Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...

09 January 2021 569 2 View

How to setup ANSYS Fluent for simulating the filling stage of an injection mould?

Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...

07 January 2021 7,992 1 View