I am working with the routing in aircraft adhoc networks. Anyone suggest suitable simulators that exhibit the nature of aircraft?
You can use NS3
You can try ADHOC Simulator.
https://pdfs.semanticscholar.org/6d9c/5c915a1e317b2e3a774c9dde865bb1890260.pdf
what are the units for those? which is scalar/vector?
10 November 2019 7,020 5 View
also, what will be the pt_ (transmission power) for 1.5 Km in ns2?
02 March 2019 2,995 6 View
Typically, copying many paras from own publication leads to self-plagiarism. As per university norms, I published required articles for PhD degree. For my thesis preparation, I want use many...
02 March 2019 5,759 2 View
if possible, What are parameters required to change for the Aircraft adhoc network simulations in NS2?
02 March 2019 2,904 3 View
Many research articles uses NS2 to experiment their work in MANET
31 December 2018 1,408 3 View
The NS2 supports energy models, but it's development is stopped since 2010. can anybody suggest simulation tool to work with energy algorithms in WSN/MANET?
31 December 2018 6,528 6 View
I would like to get the commercial license to network simulation tool that works well with WSN/MANET. Anybody suggest any good network simulation tool (to buy) for the development of novel...
31 December 2018 5,846 4 View
01 January 1970 7,571 2 View
01 January 1970 298 3 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks
24 February 2021 9,378 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...
24 February 2021 1,598 2 View
Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...
23 February 2021 1,761 1 View
Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...
22 February 2021 4,882 3 View
For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...
21 February 2021 7,624 3 View
Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...
21 February 2021 2,333 4 View