01 January 2016 1 8K Report

Hi all,

Does COMSOL use pressure poisson equation to get pressure profile?

Thanks

vivek

More Vivek Arora's questions See All
Connecting COMSOL with MATLAB?

Hi all, I want to connect matlab with COMSOL to collect data. Where i want to put a command in MATLAB and according to that command value of that parameter from the subdomain will be collected in...

11 December 2015 8,249 1 View

Solving dimensionless equations in COMSOL?

Hi,  Is it possible to solve dimensionless equations in COMSOL? How to do that? So, all post processing results will be in dimensionless form? I need some expert comment. Please someone...

11 December 2015 8,065 15 View

Any suggestions on a COMSOL Generalized alpha discretization scheme ?

Hi, Can anyone please tell me the numerical schemes used in generalized alpha scheme? Thanks Vivek

11 December 2015 8,377 0 View

Information relating to COMSOL solver?

Hi, I am using COMSOL software. I am having some problem understanding different parameters while using PARDISO linear system solver. What is pivoting perturbation? and why preordering algorithm...

11 December 2015 9,553 0 View

RTD and mixing in plug flow or in continuous reactor?

Hi all, This is going to be a purely chemical engineering thing. We know that in ideal reactor, space time (Holding time) is the tideal=Volume of reactor/Volumetric flow rate. But real reactor...

06 July 2015 1,413 21 View

Anyone familiar with convergence and under relaxation factors in fluent?

Hi , This is in relation to the effect of under relaxation factor on solution convergence.I have learned that if relaxation factors are reduced, then it takes huge time to reach the...

06 July 2015 9,948 7 View

Any suggestions on the formation of bigger and smaller eddies in turbulent medium?

Hi,  I have a question on turbulence. Turbulence causes the formation of eddies of many different length scales. Most of the kinetic energy of the turbulent motion is contained in the large-scale...

06 July 2015 5,973 69 View

What is the relation between viscous force and the inertial force?

Hi all, We all have regularly heard of the terms like viscous force and the inertial force. Now the viscous forces are the forces due to to the friction between the the layers of any real fluid....

06 July 2015 3,076 22 View

Anyone familiar with nodes and volume elements in fluent meshing CSTR?

Hi all, I was meshing a stirred tank reactor using fluent.  In the mesh statistics, it is showing that number of mesh elements are 434200 and nodes are 134420. Is it possible that nodes are so low...

04 May 2015 3,800 8 View

Finite element method?

Is there any good book for finite element methods for beginners? Which employs a  lot of examples on 3D PDE: BVP problems.

04 May 2015 5,512 3 View

Similar questions and discussions
Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View

How do I dedicate my entire life in doing only one thing?

I would like to dedicate my entire life in doing only one activity alone and nothing else. How do I achieve it in this world full of unavoidable distractions and societal pressures?

24 June 2024 298 1 View

If modulus of elasticity is divided by any inertial or dynamic pressure (1/2*rho*v^2), is there any dimensionless number present to represent it?

While deriving for a momentum equation with elastic stress effects, I am planning to put a ratio between elastic modulus (in Pa) and dynamic pressure (in Pa) in a simplified form. I am not...

23 June 2024 8,059 1 View

Trying to find a copy of an original paper?

Despite many attempts I am still unable to find the original version of this paper and would appreciate if anyone can locate it for us: Baker PG, Haig G (1981) Metronidazole in the treatment of...

20 June 2024 5,448 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close