Dear All. What is the difference between the initial gdp and the lagged gdp variable in the panel data economic growth models?

Dear All. My research topic is Financial development, economic growth and FDI. What is the difference between the initial gdp and the lagged gdp variable found in the panel data economic growth...

08 March 2019 6,910 2 View

What is the least/minimum concentration for hydrolysis probes to be processed?

My dulition target is 10 pmol for primers. I dilute primers without any problem at qpcr, multiplex pcr and classic pcr. Sometimes, I diluted probes and it didn't work. What is the least/minimum...

17 December 2014 9,924 2 View

Is there a true grammar translation method from the English language to another language (for instance, to Turkish)?

Can you give any suggestions?

12 May 2014 9,687 4 View

Can anyone give advice on how to write good project proposals and improve technical/scientific writing skills?

Can you give us an advice to write a good project proposals and improving technical/scientific writing skills?

12 May 2014 4,556 12 View

What is the electrodeposition process of copper, minerals, and metals?

see above

27 March 2014 610 1 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

Are there methods for automatically mapping floodplains, fans and terraces?

I want to map these river geoforms with as little subjectivity as possible. I have a high resolution DEM generated by drone data.

22 February 2021 7,800 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View

Could anyone suggest the appropriate composition of ball milling spheres for coal ash treatment?

I have built a ball milling to use mainly on the fragmentation of coal ash. Now I need to acquire the spheres to operate it. Steel spheres are cheap, but I am afraid they can liberate iron as it...

06 January 2021 6,433 2 View

How to build .cks file (chemkin file) in ANSYS-Forte for hydrogen-diesel dual fuel?

Dear all, I'm trying to simulate the combustion of hydrogen diesel in dual fuel mode in ANSYS-Forte. I have kinetic reaction mechanisms file( .txt) but in order to build the .cks file in the...

28 December 2020 1,570 3 View

How to calculate the flow rate required for fluidization for a fluidized bed gasifier ?

We need to calculate the flow rate of air required for fluidization of the bed. We have a compressor which gives air at 7 bar and a 1 bar rotameter for measuring the flow rate in LPM. How can I...

16 December 2020 2,092 3 View

How to integrate kinetic mechanisms for hydrogen diesel combustion for CFD analysis?

Dear all, I am writing my thesis on "CFD analysis on hydrogen assisted diesel engine". I am seeking help to construct the kinetic mechanisms for hydrogen diesel co-combustion. I managed to find...

03 November 2020 6,640 9 View

Statistical analysis via Analysis of Variance (ANOVA)?

Hello Everyone I hope everyone is doing well. I have one article in revision process in Construction & Building Materials and reviewers' are asking to do statistical analysis. However, I...

31 October 2020 7,233 5 View

Why the Graphene Oxide solution turns green instead of bright yellow in Tour's method?

I am synthesizing Graphene Oxide from Anthracite Coal. Anthracite coal was first pre-treated with 30% HNO3 for 2 hours at 80 oC temperature. Then washed with distilled water several times until...

28 October 2020 8,076 1 View

How to input engine load while performing CFD analysis on IC engines?

Hi all, I am currently writing my thesis on CFD analysis on dual-fuel hydrogen diesel engine to understand the behavior of emissions. At present I am using ANSYS Forte to conduct the CFD...

27 October 2020 3,369 3 View