What could be the cheapest way to prepare a conductive polymer ?

More Ajitanshu Vedrtnam's questions See All

What makes a cover letter impressive for the postdoc applicant if research line of target group is different than candidate's background ?

What can make the cover letter for a postdoc application impressive if the applicant is approaching for a research group having different research area from his research line? Is it fair to send...

09 October 2018 9,523 5 View

Publication rates vary widely across disciplines. Engineering, Science or biotechnology..which discipline has higher publication rate and why ?

Can publication rate of different disciplines should be compared ?

08 September 2018 8,512 9 View

Collaborator needed from Canada on "Indo-Canada Joint Call for Proposals Improving Occupant Survivability in Buildings During Fires" ?

We are looking for a collaborator from CANADA for a project Indo-Canada Joint Call for Proposals Improving Occupant Survivability in Buildings During Fires Using Innovations in Structural...

03 April 2018 8,943 0 View

What could be the possible constituents of coating to improve fire resistant of glass ?

In passive mode, boron glasses could resist fire. What could be the possible fire resistant coating constituents for glasses.

01 January 1970 5,059 1 View

With age, joy of festivals reduces ! Can't we change this ? Is there any science behind ?

I find it true, the enthusiasm and enjoy that we used to have while younger was much more than present. It may sound non technical discussion but I am curious to know Is there is any scientific...

01 January 1970 832 10 View

Which country is best, in general, for postdoc and why?

Based on "quality of research" and "remuneration" Asia, Europe, USA which region should be preferred for postdoc study.

01 January 1970 3,687 27 View

What percentage of the articles of accepted without revision in journals with an impact factor ?

Please share your own experience. For me, all the articles were accepted after a revision if the journal was with an impact factor and non paid.

01 January 1970 7,450 19 View

What materials can be used as coating materials for improving the fire resistance of opaque and transparent construction materials ?

Please share your opinion on same.

01 January 1970 8,509 4 View

What should a review article ideally include?

There are variety of approaches adopted by the authors while writing review articles. How you plan your review article ? What kind of review you prefer to read ?

01 January 1970 5,250 1 View

What makes an article interesting ?

It is surely an art to keep your readers Intetested in an technical article till the end. Could you recall the best article, why it was best for you. Originality, good English, and readability are...

01 January 1970 1,853 14 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Nizar Matar

I think that the question raised by a Research Gate colleague 2 years ago (with the answers that followed) will help in finding out where to look for cheapest made conductive polymers:

https://www.researchgate.net/post/Are_there_cheaper_polymers_that_have_similar_conductivities_than_PEDOTPSS

Bhaskar Bhatt

Sir are you asking for polymer composite?

Ajitanshu Vedrtnam

Prof. Matar,

The earlier discussion was useful but the question is still open.

PEDOT: PSS is commercially available. Could we prepare a cheaper alternative?

I am looking for the cheaper fabrication process and constituents.

Dear Bhaskar, polymer composite would do, however, transparency is a constraint.