What boat should I use to evaporate a gold contact for perovskite solar cell?

More Muhamad Zulhasif bin Mokhtar's questions See All

How do we decide BSA percentage in our buffer solution?

Hi all, I am trying to test my polymer stability in biological medium. I know how to make 1% /5% etc of BSA in buffer but I am not sure how do we actually decide this percentage volume. Is there...

05 January 2021 649 2 View

How can I write a small research article?

I am an undergraduate student of electrical engineering. I want to write an article on any topic related to electrical engineering, environment or both. But I do not know how to write it. I know...

24 December 2020 9,636 4 View

I need help in wavenet matlab code, any one help me?

I tried to use wavenet (wavelet and ANN) INSTEAD OF ANN FOR THE PURPOSE OF CLASSIFICATION

06 December 2020 864 5 View

. Any one can help me to write the slantlet matlab code?

I tried to use Slantlet transform for fault diagnosis

06 December 2020 4,987 2 View

Prevent contamination of solution in oven?

Hi all, I am trying to test stability of my electrode immersed in solution. I intent to keep them in oven for 3 weeks as to represent accelerate ageing. However, my worry is that the solution...

28 October 2020 8,351 2 View

How to simulate force transmissibility in ANSYS?

I've been trying to simulate the force transmissibility experiment based on the setup shown in the attached diagram where the transmissibility is defined as the ratio of transmitted force...

14 October 2020 9,141 2 View

Is there any effect of graphene oxide in ionic liquid?

I tried to mix polyurethane and graphene oxide with ionic liquid (EMIM-TFSI) to enhance it's ionic conductivity, will there be any effect in functional group charge (negative -cooh, -oh) of GO or...

27 May 2020 7,333 4 View

What is characteristic peak(s) in FTIR spectrum of crude plant extract?

Hello, I synthesized chitosan nanoparticles loaded with a plant extract. For confirming presence of the extract in the nanoparticles I did a FTIR analysis. Now my question is: What is...

24 January 2020 4,402 2 View

What do you suggest to me like books, articles to start working with isogeometric analysis?

I am looking to start working with the isogeometric method to analyze mechanical behavior such as beam, plate, shell and other structures of complex shapes. can you help me by giving me simple...

28 December 2019 2,729 5 View

How to ensure that a chemical synthesized peptide has correct sequence?

Dear all, I have ordered a peptide (with 32 aa) for chemical synthesis, but I dont know after receive a peptide how to ensure from its sequence. Which method(s) are available for my purpose?...

09 December 2019 3,784 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

Azhar Fakharuddin

Tungsten boat should help

Muhamad Zulhasif bin Mokhtar

Thanks Azhar. What dimension and shape would you recommend?

Chandra Bhal Singh

Use tungston boat. Use substrate holder which have cooling option so that temp of device does not increase during melting of gold.

Muhammad Imran

Alumina coated tungsten wire basket is best for gold thermal evaporation

Shrikant Chavan

Tungsten boat should do the trick. personally I have never seen device performance change with temperature. In my case, the gold layer thickness does have an impact on device performance.