What are the parameter you have included in Modeling climatic and hydrologic uncertainties?

More Firoz Ahmad's questions See All

From where i will get National park boundary of India?

03 April 2019 9,710 4 View

Can we save our world including India from Global Warming and Pollution?

Can we save our world including India from Global Warming and Pollution? Is there any remedies? What should be citizen response and government policies towards its mitigation and for sustainable...

10 November 2017 5,953 49 View

Why Delhi has so much pollution level?

10 November 2017 1,775 11 View

Crime Mapping/Analysis using GIS?

What are the technique can be applied for crime mapping/Analysis/Prediction in Indian context? Please provide reference

09 October 2017 2,789 19 View

What satellite data Forest Survey of India using for forest fire detection?

Need some literature "Forest Survey of India use satellite Moderate Resolution Imaging Spectroradiometer (MODIS) for active forest fire detection. MODIS is a key instrument on the Terra and...

09 October 2017 3,027 3 View

What is Cramer’s V coefﬁcient (CVC)?

How Cramer’s V coefﬁcient (CVC) can be calculated?

08 September 2017 8,849 10 View

How Ripley's K-statistic is calculated?

Spatial Cluster Analysis

08 September 2017 3,975 4 View

Long term deforestation assessment in Jharkhand state, India: A grid based geospatial approach

http://www.researchtrend.net/bfij/pdf/30%20BFIJ-24-2017-LAXMI%20GOPARAJU.pdf

06 July 2017 9,296 1 View

Which journal is good for publication viz. Thomson reuters vrs Scopus?

Which journal is good for publication viz. Thomson reuters vrs Scopus? How do I find the impact factor and rank for a journal?

06 July 2017 4,341 10 View

How to calculate backwater submergence of dam during full flooding?

05 June 2017 4,845 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How is energy cycled through the Earth's climate system and how do matter cycle and energy flow through the rock cycle?

08 August 2024 8,162 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View