How much Self Plagiarism allowed for PhD Thesis ?

Can we keep , our published research paper in thesis as a chapter and How much self plagiarism is allowed for Ph.D thesis ?

08 September 2017 1,200 25 View

Minimum Pressure Working Range of Capillary tube in refrigeration?

What is the lowest Delta_P , for capillary tube in refrigeration . Can capillary works under vacuum Condition i.e Condenser Pressure 50 kPa and Evaporator pressure 10 kPa ?

07 August 2016 6,551 8 View

Is anyone familiar with measuring the Adsorption Capacity of Methanol on ACF?

Dear Sir , I am performing an experiment for measurement of Adsorption Capacity of Methanol onto Indian ACF. I couldn't get adsorption and desorption properly. What should be the packing density...

08 September 2014 8,860 2 View

Which pair of Adsorbent-Refrigerant is best for solar adsorption refrigeration?

Thanks.

01 February 2014 4,396 2 View

Which method is best for measuring adsorption capacity (x or W) for ACF?

How can you determine constant ( D , W0, a and b ) in DR and DA equation for adsorption kinematics.

01 February 2014 3,350 1 View

What are the limitations of continuous adsorption refrigeration system?

Which are the Limitations of Continuous adsorption refrigeration system run by solar energy? What are the main problems for designing and fabrication of this system?

01 February 2014 9,015 4 View

What is the best quality ACF for solar adsorption refrigeration?

Can you give best quality Activated Carbon Fiber supplier or Manufacture. I am working on Solar Assisted Adsorption Refrigerator, in which ACF is used as a adsorbent.

01 February 2014 2,561 2 View

What is the flow rate of hot water for desorption and cooling water for absorption to single bed adsorber in Adsorption chiller?

01 January 1970 6,049 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View