What are the modes of heat transfer?

Maan S.M. Al-Dabbagh @Maan_Al-Dabbagh

02 February 2019 1 5K Report

Heat transfer principle

Maan S.M. Al-Dabbagh

there are three modes of heat transfer.

1. the conduction .

2. the convection.

3. the radition.

Badges
Science topic

More Maan S.M. Al-Dabbagh's questions See All

How to find strain energy release rate GI, GII, GIII in Abaqus?

I modeled a simple crack in abaqus. I get J-integral as output as well as components of stress intensity factor KI, KII, KIII. However, I do not know how to get GI, GII and GIII. I searched in...

04 January 2021 1,783 2 View

How to analysis gears contact in Asnsys static structural with frictionless contact type?

I model and simulate the contact between two gear. I applied torque on one of the gears and I fix the other using fix displacement in Ansys. Automatic contact detects the contact between gears...

20 December 2019 869 3 View

How can measured the low velocity of high air temperature?

experimental device for low velocities of gases

24 January 2019 2,137 1 View

What was the correlation obtained for average Nusselt number for free convection from incnined surfaces?

free convection from inclined surfaces

31 December 2018 6,890 0 View

What is the biot number in heat transfer? and where it used ?

what is the biot number in heat transfer? and where it used ?

31 December 2018 4,717 0 View

What is meaning of the Gratez number?

heat transfer

31 December 2018 1,314 2 View

Does any of the scholars here happen to know about a journal good for vocabulary measurement studies?

I am looking for a journal related to the foloowing title: WAT and VKS: Measures of depth but predictors of breadth of vocaulary

12 August 2018 5,492 1 View

Is it possible to upgrade python version of Abaqus?

Even the latest version of Abaqus ran with python 2.7 and it comes with numpy version 1.6. To be able to use latest version of scipy, I need to upgrade numpy. In addition, the package does not...

26 July 2018 3,348 3 View

How to write heat transfer abaqus subroutine to get steady state soultion?

I know that by using the UMATHT subroutine, one can write a heat transfer equation subroutine, but it is for transient analysis. Can I use same subroutine to get steady state solution or I must...

23 December 2017 193 3 View

What is the boundary condition between piston and cylinder in a hydraulic jack?

I intended to model a structure with a hydraulic to move it up and in addition I want to use that model to do a vibration analysis using either Ansys or Abaqus. However, I wonder, How I must model...

02 December 2017 5,948 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

Why cannot world and community leaders be gentle? Where did ethics of care go?

The whole world is in a mess and paused. We all are tired of seeing hypermasculinized and destructive leaderships all around us. This world has seen enough of the aggressive patriarchal social...

23 February 2021 292 7 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View