Please fill the survey via the link below if you have an experience in the construction industry in the UK. Do you have experience?

http://www.smartsurvey.co.uk/s/2PJWL/ Please fill this survey via this link if you have an experience in the construction industry in the UK.

03 April 2017 5,845 0 View

What is the projected water demands and wastewater discharge in the uk?

water engineering

10 November 2016 6,718 0 View

How can strategic project management be used to mitigate delays and overruns in expenditure in the construction industry?

Project management

10 November 2016 9,444 0 View

What factors affect the outcome of construction projects in uk?

10 November 2016 934 0 View

What are the factors affecting the success or failure of a construction project?

Construction and project management

10 November 2016 1,661 0 View

How do ventilated facade affect a building.

i need to know both the positive and negative effect a ventilated facade

02 March 2016 1,538 6 View

Advantages of buildings that are not environmental friendly?

merits of buildings that are not green

09 October 2015 5,325 2 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

Why anti-CD20 or other antibodies are not used to label target cells in flow cytometry t-cell cytotoxicity assay?

New to the field of cell therapy. Why fluorescent-labeled antibodies to target cell antigens are not used for determining target cell count by flow cytometry in cytotoxicity assay (eg car-t)? Cell...

21 February 2021 3,278 3 View

How to calculate time-averaged fields from Ansys CFX solver?

I would appreciate any comments on the following problem. I need to calculate mean fields (e.g. pressure, velocity and vorticity), for which I activate Trn Stats tab in CFX-Pre. However, what I...

21 February 2021 8,548 7 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View