What are the books and/or papers/ that are recommended in order to understand how wide area measurement system is modeled in the presence of delay?

04 April 2018 0 751 Report

I need to understand how WAMS can be modeled in the presence of communication time delay. it does not matter the paper or book or any other thing you propose is in power grid or computer networks.

Badges
Science topic

Similar topics
Books

More Neda Eskandari's questions See All

What are differences between types of outliers?

As far as i know there are three types of outliers: - innovation outliers - observation outliers - structrual outliers but i do not know what are differences between these three types...

10 November 2019 5,530 1 View

How distributed networked control systems(NCS) are modeled in the presence of time delay?

I need to understand how WAMS can be modeled in the presence of communication time delay. I would appreciate if you share your idea or suggest me paper, book which can be helpful.(or how...

05 June 2018 3,035 4 View

How i can estimate the voltages of buses of ieee 14 bus using pmu measurements by wls method in matlab?

i have ieee 14 bus test system that there are PMUs on 2,4,5,6,7,8,9,11 and 13 buses.by wls estimator i want to estimate voltages of buses using all measurements except the data that is collected...

01 February 2018 9,554 2 View

Is the number of PMUs effective on accuracy of power system state estimation?

for example the state vector which has been estimated with 9 number of PMUs is more accurate than the state vector which has been estimated with 4 number of PMUs?

01 February 2018 7,615 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Smart grid ideas?

How to use and this is economical?

06 August 2024 3,160 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View