I have calculated Compression Index of the subsurface soils. I would like to know the role of Compression index in Geotechnical & Geological sciences. Is there any range of the Cc values to make hazard/geotechnical map?
Use in determining the settlement characteristics of a soil with respect to loading
Thanks Mala. Could you pls suggest any paper or report related to its application?
You should check on geotechnical engineering books.
I am removing carbonates from clay and sand samples. So, I treat the sediments with H2O2. I need to wash the sediments to remove acid residues. I am thinking of heating the sediments with...
11 December 2019 2,946 6 View
Clay samples are heated at 950 degree centigrade (LOI method) before XRF analysis. Due to which Fe percentage increases in the XRF results. It is due to the oxidation of samples during fusion. Is...
11 December 2018 1,037 5 View
I have calculated Liquid Limit, Plastic Limit, Soil type, SPT and Fine Contents.How can it be applied in urban development especially making some zonal maps, risk factors, bearing capacity,...
31 December 2017 6,844 12 View
Dear all, I have calculated Fine content (Silt+Clay), Liquid Limit, Plastic Limit, Plasticity Index, Mean grain size, SPT value for soil samples. I need to obtain Clay % for my study. Kindly...
31 December 2017 5,742 9 View
Dear all, I have collected soil samples up to a depth of 50m from surface during drilling. I need to interpret alternate cycles of dry and wet climate on the basis of soil types. What are the...
10 November 2017 5,058 6 View
Dear all, I have done XRD analyses of modern fluvial unconsolidated sediments (soil- clay, silt and sand) to identify the mineralogy and their proportions. I require to select the best minerals...
10 November 2017 7,916 8 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View