What are the advantages of low voltage RF MEMS varactor?

06 December 2018 1 4K Report

I am working on RF MEMS vatractor that require low voltage almost 3.8V using electrostatic actuators .what are the advantages of low voltage?

Nagarjun Bhat

Is it concerned with low power consumption?

Badges
Science topic

More Ayesha Akhtar's questions See All

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Articles on" Gender disparities i leatherwork education"?

Articles on" Gender disparities i leatherwork education"

07 August 2024 2,500 0 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Why reactivity isn't increased with more empty spots in valence shell?

If from a geometric perspective the non-halogens, non-noble gases have more empty spots in their valence shell, and the filling/exiting of any of the empty spots in the shell constitutes a...

03 August 2024 4,787 2 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Why don't d-orbitals split themselves, why does it take a ligand? why don't protons from ligand repel nucleus split d-orbitals?

why don't d-orbitals split themselves because of themselves without the presence of ligands? Electrons are indistinguishable. Why wouldn't it be more correct that protons from a ligand split the...

03 August 2024 3,589 3 View

Why doesn't chromium 2+ ion use all its d-orbitals to receive lone pairs from six waters in [Cr(H20)6)]3+?

I'm guessing it's because the ligand experiences too much electron repulsion or proton repulsion from the chromium to insert them close to the 3d-orbitals which are close to the metal nucleus. Is...

03 August 2024 1,370 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What should I upgrade in my computer to speed up simulation in CST?

I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...

10 July 2024 2,789 4 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

How to troubleshoot error E1 on Biorad Powerpac Basic despite using sufficient and fresh buffer?

I have used this BIorad Powerpac Basic for 4 years now, before which it was used for another 5-6 years. Generally we addressed the E1 error by compensating with fresh buffer and/or filling the...

01 July 2024 7,104 1 View

Self discharge of freshly made NMC half cells and voltage stabilizes at 3.3-3.5 V vs Li/Li+ during charging. What can affect it?

I am making Li half cells using NMC as cathode. The OCV is around 3 V but it self discharges and during charging the voltage increases to 3.5 V and then drops to 3.3-3.4 V and stays there. I have...

23 June 2024 842 3 View

How to predict the efficiency of a very low speed Railgun Actuator/Lorentz Force Actuator?

I'm not an electrical engineer or anything related to that subject, so my apologies if I understood something incorrectly. Well, I read somewhere that the slower the railgun is, the higher its...

23 June 2024 1,082 0 View

How to avoid SS contamination in RF magnetron sputtering?

Hello I am encountering Fe and other stainless steel (SS) element contamination in my LiCoO2 RF sputtering depositions. I suspect the source is the "etching" of the magnetron stainless steel frame...

11 June 2024 2,196 3 View