Two-pass solar air heater has a 30 mm air gap for each duct. Is airflow inlet from either the lower or upper duct to achieve optimum effectiveness?
Yes, it is going to achieve as heat transfer to the surrounding air will be through convection current.
I appreciate your responses Manford M, and Jie D , thank .
Dear Salah,
It seems that there are earlier reported literature available when airflow inlet is through the upper as well as the lower channel. All depends upon the operating conditions, and how you have optimized them.
Many thanks, dear Mr. Arun Raj. You are welcome.
Following answers.
Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...
03 March 2021 9,989 2 View
Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...
23 February 2021 5,827 3 View
What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...
21 February 2021 9,273 2 View
Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...
21 February 2021 8,659 1 View
Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...
21 February 2021 6,197 1 View
According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...
21 February 2021 5,919 9 View
Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...
17 February 2021 1,709 3 View
A software which can help to design the experiment, store data, update new data, set subculture reminders, barcoding etc. Like Invitrosoft.
17 February 2021 3,015 5 View
Hello, I would like to do homomorphic encryption using Microsoft SEAL on my dataset and then use it as an input to the Cloudsim simulator to do clustering on. Is it possible and compatible with...
16 February 2021 3,915 1 View
Hi, I'm trying to merge files from a data base of 20 files, each containing about 4000 subjects. Unfortunately the ID numbers are actually a combination of numbers and letters (e.g., b1458219)....
15 February 2021 5,833 3 View
Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...
03 March 2021 961 3 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...
02 March 2021 2,246 2 View
I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...
01 March 2021 5,023 5 View
I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...
28 February 2021 1,638 3 View
I have a doubt on how to select the inductor and capacitor value when I want to implement MPPT controller. This is because we always take a maximum output voltage and current but in this case, we...
28 February 2021 3,637 2 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View
I am working on creating deep neural network on geospatial dataset and wanted to know how to do the sampling so that I can increase the presence of solar panels in the images. I cannot use entire...
25 February 2021 3,936 6 View
As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...
24 February 2021 1,349 1 View
Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...
23 February 2021 1,908 2 View