25 November 2012 0 4K Report

I can't compile Circos display because the module "Config::General" is not usable. Anyone knows where and how I can use this module?

More Juan Sebastian Lugo Ramos's questions See All
What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

HPLC baseline failure (ACN/Water)?

My baseline increases without any explanation, it is only fixed by changing the solution B, will it be the column? Reagents? Bomb? Detector? Solution A: H3PO4 0.01% IN WATER Solution B: H3PO4...

21 February 2021 5,656 3 View

Algorithms to filter corrective max and min from a set of data?

I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...

17 February 2021 2,777 5 View

How to improve the buffer capacity of sea water?

Hello everyone I would like to improve the buffer capacity of seawater (pH ~8) in order to dissolve as much CO2 as possible without dropping the pH below 7.5 (a range between 7 - 7.5 is...

17 February 2021 2,797 2 View

Resume Book UEP2013 Asian Edition, dis somebodey has it?

I am looking for a copy of the resume book of UEP2013 Asian Edition (Urban Environmental Pollution 2013 Asian Edition) held in Beijing. If somebody has it, please I would like to obtain an...

11 February 2021 2,247 2 View

Can anyone recommend a scale to measure Bloom's taxonomy of learning styles?

I am looking for recommendations of scales (in English or Spanish) to measure learning styles according to Bloom's taxonomy of learning. Thank you in advance!

09 February 2021 1,419 8 View

How do they fill/replace metal hydrides in vessels?

Surely they will want to avoid contact with air/moisture, so what is the procedure for this?

23 January 2021 428 2 View

What type of spectral radiation has greater penetration on materials, UV or IR? What book or source do you recommend for information on this?

I need information concerning the penetration and reflection capacity of ultraviolet and infrared radiation wavelengths on different most common materials. Edit. Can somebody recommend a book to...

16 January 2021 8,051 6 View

What is the easiest and cheapest molecular magnet to synthesize at home and how can it be done?

im looking for a diy at home (home lab) molecular magnet in a chemical suspension that is stable at room temperatures and cheap

30 December 2020 626 1 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close