Triple TOF LC/MS/MS was done on the plant material am working on, I dont know how to interprete my result, I need assitance who will be co-authour?

More Tope Atere's questions See All

What is the maximum ml of extract in a vehicle that can be administered to rats of 100g, subcutaneously and intramuscularly?

Subcutaneous and intramuscular route of administration.

02 April 2024 8,998 0 View

Which solvent is best used to administer aqueous ethanolic extracts to rats?

can distilled water be used to administer aqueous ethanolic extracts to rats?

15 March 2024 3,560 1 View

What significance is fractionating from powdered plant sample over an organic solvent extract?

comparison of fractions from powdered plant sample and an organic solvent extract

12 May 2023 6,342 3 View

Is there a minimum number of studies to include in a meta-analysis?

What is the lowest number of studies that must be available before conducting a meta-analysis?

29 March 2023 7,053 3 View

How can i define a composite section of an I-steel beam with concrete deck on it using SAP2000?

I am trying to do a load rating of a steel truss bridge and needed to get the section modulus and thereafter of the Interior steel girder. Please i need assistance on how to define the section of...

01 September 2021 9,610 3 View

How can I improve translation and rotation in the x, y and z direction in my finite element model?

I created a finite element model of a steel truss bridge and the modal mass participation reveals only translation in the y direction only for the first 30 modes. I need help to solve this...

09 May 2021 5,071 2 View

Could someone state or predict if 'Journal of Ayurvedic and herbal medicine is a Predatory journal?

Journal in which I was ask to pay publication charge for my manuscript already accepted and find attached, the snapshots of the payment as requested. Your professional response will be highly...

29 April 2021 8,412 6 View

How can i resolve problems relating to SAP 2000 model of a bridge adding more constraints on its own when i want to do a modal analysis?

I created a finite element model of steel truss bridge and tried to do a modal analysis to generate the natural frequencies and mode shapes. Unfortunately, i don't get deformed shapes, but rather...

25 April 2021 881 6 View

Administered dose to animals?

Can someone explain how to calculate 2g/kg/body weight dose of any extract to be administered to animal of 500kg. Your response will be greatly appreciated?

12 April 2019 7,310 6 View

Which class are Fatty constituents?

Which of the class do fatty phytoconstituents usually extracted with hexane/pet ether belong within the following, Alkaloid, phenolics and terpenoid?

08 April 2019 4,428 9 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

How do soil microflora interact with plant roots and influence plant nutrition, health, and productivity?

06 August 2024 9,618 3 View

Are there instances where molecules with larger molecular weights exhibit greater mobility than those with smaller molecular weights?

Hi, I know that low molecular weight (MW) molecules generally tend to have higher mobility, while high molecular weight molecules tend to have lower mobility. However, in my experimental...

06 August 2024 1,495 2 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View

For an in-vitro drug release study, what molecular weight cut-off (MWCO) dialysis bag is required for a 117 kDa protein?

kindly reply me. Thanking you in advance.

05 August 2024 7,727 4 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

How can I interpret the data without the need of solving it manually?

How can I interpret the data gathered without solving?

03 August 2024 9,054 3 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View