Dear readers,
How to assign to each interior-zone a pressure value ?
You will find enclosed a picture that illustrates my problem.
Best regards.
You can easily do it using patch option fluent. All you need to do is to define cylindrical space and assign your calculated pressure value.
I have prepared half cell. Lithium is considered as anode in the system. Whereas, I would like to know what is actually capacity retention? How it can be calculated mathematically? On what factors...
02 June 2024 4,135 0 View
I have been working on electrospun membrane for Lithium Ion coin cells. I have tried to control different parameters, such as, thickness, electrolyte amount and many other parameters. I am facing...
26 March 2024 2,786 0 View
Everything is standardized as per protocol, but still this smearing is there, need suggestions from PCR experts. DNA extraction by the magnetic beads-based method. tried colony Pcr. PCR...
01 January 2024 6,888 4 View
As i asked in the question statement, I observed a little amount of PP is soluble in cyclohexane. If i want to prepare a 4 %w/w solution of PP in cyclohexane, it is obvious all of it will not be...
03 November 2023 5,905 4 View
I dissolved a medium molecular weight polymer at 135 degree celcius and after removing it from flask, i poured it into glass bottle for further use but it became a gel like structure. Can anyone...
03 September 2023 8,436 3 View
SCAPS-1D software for perovskite solar cell simulation.
01 September 2023 4,219 0 View
for perovskite absorbers like (bandgap (eV),electron affinity (eV),dielectric permittivity (relative),CB effective density of states (1/cm^3),electron thermal velocity (cm/s),electron mobility...
27 August 2023 2,194 2 View
27 August 2023 3,500 2 View
Is high molecular weight PLA a good choice for application in elastomers? The molecular weight (Mw) of PLA I am planning to use is 80000. Kindly suggest if other biopolymers are suitable instead...
28 May 2023 5,401 1 View
I have to use poly lactic acid for one of my experiments. The weight average molecular weight of poly lactic acid is 80,000. How i can convert Mw to Mn in order to calculate given amount of mass...
23 April 2023 2,418 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...
11 July 2024 5,380 0 View
What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?
05 July 2024 1,891 0 View
Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...
30 June 2024 6,004 0 View
I would like to dedicate my entire life in doing only one activity alone and nothing else. How do I achieve it in this world full of unavoidable distractions and societal pressures?
24 June 2024 298 1 View
While deriving for a momentum equation with elastic stress effects, I am planning to put a ratio between elastic modulus (in Pa) and dynamic pressure (in Pa) in a simplified form. I am not...
23 June 2024 8,059 1 View
Despite many attempts I am still unable to find the original version of this paper and would appreciate if anyone can locate it for us: Baker PG, Haig G (1981) Metronidazole in the treatment of...
20 June 2024 5,448 3 View