What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Are protein samples in SDS compatible with ELISA?

I have used an AllPrep DNA/RNA/Protein Mini Kit QIAGEN kit to extract RNA and protein from my samples. At the end of the protein purification, I resuspend my protein in 5% SDS. Will these samples...

28 February 2021 7,370 3 View

Special issue on PLS-SEM in Mathematics. Are you interested?

21 February 2021 5,601 3 View

How to calculate the TCID50 when the highest CPE is 50% or less?

I am doing TCID50 to measure progeny virus and some treatments protected the cells in a way that the highest CPE observed is 50% or less. How should I do the titre calculation in that case? Thank you!

16 February 2021 8,768 1 View

Which drug is better to modify blood pressure in awake monkey, if I provide it in the food or drink reward?

I need to modify the blood pressure in a monkey while is awake in the recording chamber, and I am planing on provide a drug for that in the food or water used for reward... any advise? Thank you

08 February 2021 9,900 1 View

Why stop the reaction in ice for the fluorescent probe FDA (fluorescein diacetate)?

Hi, In literature I noticed that who stains haemocytes with FDA for 30 min then stop the reaction in ice while this does not apply for 15 min incubation time (or maybe authors did not write this...

08 February 2021 3,366 3 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Why do high doses of humic substances inhibit the growth of corn roots? Is there a toxicity effect?

Length, volume, surface area and dry mass of corn roots treated with humic substances increased up to 13 liters per hectare and decreased with higher doses.

02 February 2021 2,190 4 View

Using a nucleosil c18 column, i get no negative peaks in real time and two negative peaks in post run.Software problem?

Simadzu, lc solutions

02 February 2021 1,969 2 View

Any ideas on fast and easy way to stain mucus on intact cell layer?

Dear RG community, We are looking for a fast and easy way to stain mucus on a cell layer that allows for macroscopic visualization of mucus distrubution. Our epithelium is grown in conventional...

31 January 2021 6,790 2 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View